LiRover
superyeetyash·LiRover·pcb/pcb.kicad_pcb
About the LiRover PCB
LiRover is an open source Raspberry Pi PCB design by superyeetyash, published on GitHub under the MIT license. It is a 2-layer board measuring 94 × 92 mm, with 12 components from 10 distinct parts.
Its main chip is the RaspberryPi_Pico_W, from the Raspberry Pi family. By type, the board carries 4 capacitors, 1 module, 1 connector and 1 fuse.
It belongs with the sensors and robotics & motion designs in this gallery.
From the project
Welcome to LiRover! This hardware for Hackclub's Stardance event will be centered around a hardware initiative by 4 high schoolers.
Welcome to LiRover! This hardware for Hackclub's Stardance event will be centered around a hardware initiative by 4 high schoolers.
After a failed rocket idea, we settled on an RC car with a LiDAR sensor attached that can create a comprehensive map of its surroundings. This is done from scratch by creating a 3D printed chassis, custom PCB, and an embedded control system. This project is controlled through a Raspberry Pi Zero 2 W and a Raspberry Pi Pico W. The robot will combine LiDAR sensing, an IMU (which includes an accelerometer for linear acceleration, gyroscope for measuring angular…

Main components on the LiRover
LiRover bill of materials (BOM)
12 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RaspberryPi_Pico_W | RaspberryPi_Pico_W_SMD_HandSolder | A1 |
| 1 | Screw_Terminal_01x02 | PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | 2A | Fuse_1206_3216Metric | F1 |
| 2 | Conn_01x04 | PinSocket_1x04_P2.54mm_Vertical | J_BARO1, J_IMU1 |
| 1 | Screw_Terminal_01x04 | PinHeader_1x04_P2.54mm_Vertical | J_LIDAR1 |
| 1 | Conn_02x20_Odd_Even | PinSocket_2x20_P2.54mm_Vertical | J_PI1 |
| 1 | Conn_01x06 | PinSocket_1x06_P2.54mm_Vertical | J_SD1 |
| 1 | 220uF | CP_Radial_D6.3mm_P2.50mm | C1 |
| 2 | 100nF | C_Disc_D7.5mm_W5.0mm_P5.00mm | C2, C6 |
| 1 | 10uF | CP_Radial_D6.3mm_P2.50mm | C5 |
LiRover design files
The KiCad project lives in the superyeetyash/LiRover repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/pcb.kicad_pcb
- Schematicpcb/pcb.kicad_sch
- BOMBOM.csv
LiRover: common questions
What microcontroller does the LiRover use?
The LiRover is built around the RaspberryPi_Pico_W, from the Raspberry Pi family.
How big is the LiRover PCB?
The LiRover measures 94 × 92 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the LiRover?
12 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the LiRover design files?
From the superyeetyash/LiRover repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the LiRover design in my own project?
Yes, under the terms of its MIT license, which superyeetyash chose for the repository.
Can I test firmware for the LiRover without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.
Similar boards
Raspberry Pi
Open source rover
nasa-jpl
220 × 178 mm144 parts2LApache-2.09.7kRaspberry Pi
Iot
dotnet
56 × 65 mm24 parts2LMIT2.4kRaspberry Pi
SPIRIT
SPIRIT-org
82 × 155 mm130 parts6LCERN-OHL-S-2.01.3kRaspberry Pi
CM5RevEng
schlae
55 × 40 mm417 parts10LNo license1.0kRaspberry Pi
Haxo hw
cardonabits
102.4 × 211.3 mm38 parts2LCustom license673Raspberry Pi
Phased
Neumi
75 × 100 mm71 parts2LNo license507