MITE-ESC
SySch415·MITE-ESC·hardware/crawler_schematic/crawler_schematic.kicad_pcb
About the MITE-ESC PCB
MITE-ESC is an open source STM32 PCB design by SySch415, published on GitHub under the MIT license. It is a 4-layer board measuring 40 × 50 mm, with 70 components from 48 distinct parts.
Its main chip is the STM32F411CEUx, from the STM32 family. Other key parts include the RY8336, TB6612FNG and NRF24L01. By type, the board carries 5 ICs, 5 resistors, 3 connectors, 2 LEDs, 2 inductors and 2 capacitors.
It belongs with the rf & radio designs in this gallery.
From the project
Electronic Speed Controller for SCX24 rock crawlers
A from-scratch Electronic Speed Controller for SCX24 rock crawlers, built around the STM32F411. It has two parts:
- Crawler: receives commands over a 2.4 GHz nRF24L01+ link and drives a brushed 050 motor through a TB6612FNG H-bridge plus a steering servo. Its custom board is MITE v1, shown above. - Controller: a handheld transmitter that reads a 2-axis joystick and sends throttle and steering to the crawler.

Main components on the MITE-ESC
MITE-ESC bill of materials (BOM)
70 components, 48 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32F411CEUx | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 2 | RY8336 RYCHiP(蕊源) | ESOP-8_L4.9-W3.9-P1.27-LS6.0-BL-EP-1 | U2, U3 |
| 1 | TB6612FNG | SSOP-24_5.3x8.2mm_P0.65mm | U4 |
| 1 | NRF24L01 | QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm | U6 |
| 1 | Motor_Servo | PinHeader_1x03_P2.54mm_Vertical | M2 |
| 1 | AO4407A AOS | SOIC-8_L4.9-W3.9-P1.27-LS6.0-BL | Q1 |
| 2 | JST-PH | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J1, J2 |
| 1 | SWD_Header | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | 50ohm | Johanson_2450AT43F0100 | AE1 |
| 1 | boot switch | SW_Push_1P1T_NO_CK_KMR2 | BOOT0 |
| 6 | Opt. | C_0603_1608Metric | CFF_3.3, CFF_5, C_ref_1, C_ref_2, C_ref_3, C_ref_4 |
| 2 | 22uF | C_0603_1608Metric | CIN_3.3, CIN_5 |
| 2 | 22x2uF | C_0603_1608Metric | COUT_3.3, COUT_5 |
| 2 | 10uF | C_0603_1608Metric | C_H_1, C_H_2 |
| 1 | 47uF | CP_Elec_6.3x5.4 | C_H_3 |
| 2 | 4.3pF | C_0603_1608Metric | C_M_1, C_M_2 |
| 1 | 2.2uF | C_0603_1608Metric | C_M_3 |
| 3 | 100 nF, X7R, 16 V | C_0402_1005Metric | C_M_4, C_M_5, C_M_6 |
| 1 | 100 nF, X7R | C_0402_1005Metric | C_M_7 |
| 2 | 10nF | C_0402_1005Metric | C_nrf_1, C_nrf_11 |
Show 28 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1nF | C_0402_1005Metric | C_nrf_2 |
| 1 | 33nF | C_0402_1005Metric | C_nrf_3 |
| 1 | 1.0pF | C_0402_1005Metric | C_nrf_4 |
| 1 | 1.5pF | C_0402_1005Metric | C_nrf_5 |
| 1 | 4.7pF | C_0402_1005Metric | C_nrf_6 |
| 1 | 2.2nF | C_0402_1005Metric | C_nrf_7 |
| 2 | 22pF | C_0402_1005Metric | C_nrf_8, C_nrf_9 |
| 1 | 100nF | C_0603_1608Metric | C_rst_1 |
| 1 | 10uH +-10% | L_0603_1608Metric | L_M_1 |
| 1 | 8.2nH | L_0402_1005Metric | L_nrf_1 |
| 1 | 3.9nH | L_0402_1005Metric | L_nrf_2 |
| 1 | 2.7nH | L_0402_1005Metric | L_nrf_3 |
| 2 | 10K | R_0603_1608Metric | R_B_1, R_B_2 |
| 2 | 10 kOhm | R_0603_1608Metric | R_EN_3.3, R_EN_5 |
| 1 | 10k Ohm | R_0603_1608Metric | R_H_1 |
| 1 | 1K | R_0603_1608Metric | R_L_1 |
| 1 | 5.1K | R_0603_1608Metric | R_L_2 |
| 1 | 22k | R_0603_1608Metric | R_nrf_1 |
| 1 | 1M | R_0603_1608Metric | R_nrf_2 |
| 1 | NC | R_0603_1608Metric | R_rst_1 |
| 2 | Crystal_4pin_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y_M_1, Y_nrf_1 |
| 1 | LED_pc13 | LED_0805_2012Metric | D_L_1 |
| 1 | LED_pwr | LED_0805_2012Metric | D_L_2 |
| 2 | 4.7uH | IND-SMD_L3.0-W3.0_FTC303020D | L1_3.3, L1_5 |
| 2 | 100nF | C_0603_1608Metric | C1_3.3, C1_5 |
| 1 | 25.68 kOhm | R_0603_1608Metric | R1_3.3 |
| 3 | 10 kOhm | R_0603_1608Metric | R1_5, R2_3.3, R3_5 |
| 1 | 44.05 kOhm | R_0603_1608Metric | R2_5 |
MITE-ESC design files
The KiCad project lives in the SySch415/MITE-ESC repository on GitHub; these links point at the commit this page was built from.
MITE-ESC: common questions
What microcontroller does the MITE-ESC use?
The MITE-ESC is built around the STM32F411CEUx, from the STM32 family.
How big is the MITE-ESC PCB?
The MITE-ESC measures 40 × 50 mm, has 4 copper layers and is 1.565 mm thick.
How many components are on the MITE-ESC?
70 components, from 48 distinct parts. The full bill of materials is listed on this page.
Where can I download the MITE-ESC design files?
From the SySch415/MITE-ESC repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the MITE-ESC design in my own project?
Yes, under the terms of its MIT license, which SySch415 chose for the repository.
Can I test firmware for the MITE-ESC without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k