ClockDivider

System-J-Synthesizers·ClockDivider·pcb/clock_divider.kicad_pcb

ClockDivider PCB layout, top view — open source STM32 board by System-J-Synthesizers

About the ClockDivider PCB

ClockDivider is an open source STM32 PCB design by System-J-Synthesizers, published on GitHub. It is a 2-layer board measuring 100 × 78 mm, with 73 components from 30 distinct parts.

Its main chip is the STM32G441KBTx, from the STM32 family. Other key parts include the LM358, LM7805_TO220, LM317_TO-220, 74LS08 and 74HC138. By type, the board carries 24 resistors, 16 connectors, 12 capacitors, 10 diodes, 7 ICs and 2 transistors.

From the project

DIN Sync Clock Divider

Main components on the ClockDivider

ClockDivider bill of materials (BOM)

73 components, 30 distinct parts.

QtyPartRefs
1
LM358
U1
1
LM7805_TO220
U2
1
LM317_TO-220
U3
1
74LS08
U4
1
STM32G441KBTx
U5
1
~
U6
1
74HC138
U7
2
BC807
Q1, Q2
1
V+
J1
1
GND
J2
1
20-0975
DC
J3
1
20-0551
J4
1
BATT
J5
5
AudioJack2
J6, J7, J8, J9, J10
1
DEBUG
J11
5
Conn_01x02_Pin
J12, J13, J14, J15, J16
2
SW_SPST
SW1, SW2
6
LED
D1, D2, D3, D4, D5, D6
1
CH1
D7
1
CH2
D8
Show 10 more
QtyPartRefs
1
CH3
D9
1
CH4
D10
8
100n
C1, C2, C3, C6, C8, C9, C10, C13
4
1u
C4, C5, C7, C11
1
390R
R1
2
2.2k
R2, R4
2
3.3k
R3, R5
2
470R
R6, R8
16
1k
R7, R9, R11, R12, R13, R14, R15, R16 +8
1
10k
R10

ClockDivider design files

The KiCad project lives in the System-J-Synthesizers/ClockDivider repository on GitHub; these links point at the commit this page was built from.

ClockDivider: common questions

What microcontroller does the ClockDivider use?

The ClockDivider is built around the STM32G441KBTx, from the STM32 family.

How big is the ClockDivider PCB?

The ClockDivider measures 100 × 78 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the ClockDivider?

73 components, from 30 distinct parts. The full bill of materials is listed on this page.

Where can I download the ClockDivider design files?

From the System-J-Synthesizers/ClockDivider repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the ClockDivider design in my own project?

The repository has no license, so all rights stay with System-J-Synthesizers. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the ClockDivider without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards