400 open source boards using the LM358

Real designs built with the LM358, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

400 boardsClear filters|Most starred

How designs wire the LM358

Read from the KiCad layouts of 295 open source designs, one per repository: what each pin of the LM358 connects to, and the resistors, capacitors and other passives placed on it.

  • The - pins have a series resistor on 201 of 295 designs, most often 10 kΩ (then 1 kΩ).
  • The O1 pin has a series resistor on 199 of 295 designs, most often 10 kΩ (then 1 kΩ).
  • The V- pin is tied to GND on 238 of 295 designs (not connected on 2, -12V on 28, a signal on 27).
  • The + pins have a series resistor on 147 of 295 designs, most often 10 kΩ (then 1 kΩ).
O1pin 1Connected to: Signal 94%
  • Series resistor on 67% · 10 kΩ (39), 1 kΩ (36), 100 kΩ (22)
-pin 2, 6Connected to: Signal 78%
  • Series resistor on 68% · 10 kΩ (92), 1 kΩ (57), 100 kΩ (44)
  • Resistor to GND on 33% · 10 kΩ (35), 1 kΩ (27), 100 kΩ (7)
+pin 3, 5Connected to: Signal 76%
  • Series resistor on 50% · 10 kΩ (76), 1 kΩ (28), 100 kΩ (25)
  • Resistor to GND on 40% · 10 kΩ (48), 100 kΩ (25), 1 kΩ (11)
V-pin 4Connected to: GND 81%
O2pin 7Connected to: Signal 69% · not connected 29%
  • Series resistor on 50% · 10 kΩ (35), 1 kΩ (27), 100 kΩ (18)
V+pin 8Connected to: 5V 83% · a signal 15%
  • Decoupling capacitor on 46% · 100 nF (122), 10 µF (12), 1 µF (9)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Stmbl 4.0 by rene-dev, RFBitBanger by profdc9, EV Charger by fotherja and Core by shmoergh.

The LM358 in open source designs

The gallery holds 400 open source boards using the LM358 from 310 GitHub repositories; a typical one measures about 88.9 × 78 mm and carries around 60 components.

84% are two-layer designs, the rest use four layers or more, and 37% carry an open source license.

The most starred is Stmbl 4.0 by rene-dev.

LM358: common questions

Where can I find a LM358 reference design?

Each of the 400 boards on this page is a real design using the LM358. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the LM358 - pin?

The - pins have a series resistor on 201 of 295 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 295 open source designs using the LM358.

What resistor goes on the LM358 O1 pin?

The O1 pin has a series resistor on 199 of 295 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 295 open source designs using the LM358.

How is the LM358 V- pin connected?

The V- pin is tied to GND on 238 of 295 designs (not connected on 2, -12V on 28, a signal on 27). Counted from the KiCad layouts of 295 open source designs using the LM358.

What parts are used alongside the LM358?

The AMS1117-3.3, L7805, LM7805_TO220, USBLC6-2SC6 and 74HC595 appear in the most repositories here.

Which microcontrollers do boards using the LM358 use?

Most are built on AVR/Arduino (63), ESP32 (31), RP2040/RP2350 (29) and STM32 (26).

How big is a typical board using the LM358?

The median is 88.9 × 78 mm, and 84% are two-layer designs.

What is the most popular open source board using the LM358?

By GitHub stars, Stmbl 4.0 by rene-dev, with 979 stars.

Can I simulate one of these boards using the LM358 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part