Chris Controller
tdevince·Chris-Controller·KiCad 9.0 Files/Chris Controller.kicad_pcb
About the Chris Controller PCB
Chris Controller is an open source ESP32 PCB design by tdevince, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 40.6 × 60.4 mm, with 20 components from 18 distinct parts.
Its main chip is the ESP32_S2_Solo_2, from the ESP32 family. Other key parts include the C7073593. By type, the board carries 9 capacitors, 4 connectors, 4 resistors, 2 ICs and 1 switch.
From the project
Project to create a remote control system for oxygen concentrators
This folder contains the KiCad files for the schematic and PCB layout in the formate required by JLCPCB.com. Also included is the BOM and position file that JLCPCB requires for assembly. The BOM and postion file do not include information the push buttons, connectors or ESP32-S2-Solo-2 module since these are manually soldered after receipt of the manufactured PCB's.
Main components on the Chris Controller
Chris Controller bill of materials (BOM)
20 components, 18 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C7073593 TPSM33625 | QFN-FCMOD | U1 |
| 1 | ESP32_S2_Solo_2 | ESP32_S2_SOLO_2 | U2 |
| 1 | ULN2003A Connector | DIP-16_W7.62mm_Socket | J1 |
| 1 | CON-SOCJ-2155 | GRAVITECH_CON-SOCJ-2155 | J2 |
| 1 | 28BYJ-48 | JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J3 |
| 1 | 3590S Pot | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | OTA | SW_PUSH_6mm_H5mm | SW1 |
| 1 | C29823 4.7uF | C_1206_3216Metric | C1 |
| 1 | C307331 100nF | C_0402_1005Metric | C2 |
| 1 | C1848 1uF | C_1206_3216Metric | C3 |
| 3 | C45783 22uF | C_0805_2012Metric | C4, C5, C6 |
| 1 | C52923 1uF/25V(10%) | C_0402_1005Metric | C7 |
| 1 | C96446 10uF/25V(20%) | C_0603_1608Metric | C8 |
| 1 | C14663 0.1uF/50V(20%) | C_0603_1608Metric | C9 |
| 1 | C23352 24k | R_0603_1608Metric | R1 |
| 1 | C25804 10k | R_0603_1608Metric | R2 |
| 1 | C25744 10K | R_0402_1005Metric | R3 |
| 1 | C31850 22k | R_0603_1608Metric | R4 |
Chris Controller design files
The KiCad project lives in the tdevince/Chris-Controller repository on GitHub; these links point at the commit this page was built from.
Chris Controller: common questions
What microcontroller does the Chris Controller use?
The Chris Controller is built around the ESP32_S2_Solo_2, from the ESP32 family.
How big is the Chris Controller PCB?
The Chris Controller measures 40.6 × 60.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Chris Controller?
20 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Chris Controller design files?
From the tdevince/Chris-Controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Chris Controller design in my own project?
Yes, under the terms of its GPL-3.0 license, which tdevince chose for the repository.
Can I test firmware for the Chris Controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Chris-Controller
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k