Project
teamantariksh-satellites·PCB-design-training·students/samarth-bn/kicad_project/project.kicad_pcb
About the Project PCB
Project is an open source AVR/Arduino PCB design by teamantariksh-satellites, published on GitHub. It is a 2-layer board measuring 91.2 × 65.6 mm, with 6 components from 6 distinct parts.
Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. By type, the board carries 2 connectors, 1 module, 1 diode, 1 capacitor and 1 resistor.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
A shield interface board designed to connect an HC-SR04 ultrasonic distance sensor and a standard 5V servo motor directly to an Arduino Nano. It acts as an automated door system controller. The primary goal of this board is to replace unstable breadboard jumper wires with a robus
A shield interface board designed to connect an HC-SR04 ultrasonic distance sensor and a standard 5V servo motor directly to an Arduino Nano. It acts as an automated door system controller. The primary goal of this board is to replace unstable breadboard jumper wires with a robust, etched physical PCB that will not disconnect during the physical vibrations of the servo actuating. The final revision includes a decoupling capacitor for sensor power stability and a status LED.
Main components on the Project
Project bill of materials (BOM)
6 components, 6 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 1 | Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Conn_01x03 | PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | LED | LED_D5.0mm | D1 |
| 1 | C | C_Disc_D5.0mm_W2.5mm_P2.50mm | C1 |
| 1 | R | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
Project design files
The KiCad project lives in the teamantariksh-satellites/PCB-design-training repository on GitHub; these links point at the commit this page was built from.
Project: common questions
What microcontroller does the Project use?
The Project is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.
How big is the Project PCB?
The Project measures 91.2 × 65.6 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Project?
6 components, from 6 distinct parts. The full bill of materials is listed on this page.
Where can I download the Project design files?
From the teamantariksh-satellites/PCB-design-training repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Project design in my own project?
The repository has no license, so all rights stay with teamantariksh-satellites. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Project without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in PCB-design-training
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k