Simple sensor with easyC
test-gh-syncer2·Soldered-Simple-sensor-with-easyC-breakout-hardware-design·CAD/V1.1.1/Simple_sensor_easyC.kicad_pcb
About the Simple sensor with easyC PCB
Simple sensor with easyC is an open source AVR/Arduino PCB design by test-gh-syncer2, published on GitHub under the TAPR-OHL-1.0 license. It is a 2-layer board measuring 38 × 22 mm, with 18 components from 11 distinct parts.
Its main chip is the ATTINY404-SSNR, from the AVR/Arduino family. By type, the board carries 6 relays, 4 resistors, 2 capacitors, 1 IC and 1 diode.
It belongs with the sensors and dev boards & breakouts designs in this gallery.
From the project
Hardware design, BOM, gerbers, 3D files and pinout for Simple-sensor-with-easyC-breakout designed by Soldered.
All Soldered hardware is designed in KiCAD, and repositories are organized in the following way:
- CAD folder - contains KiCAD files (Schematics, Board, Panel Board), organized by version. Change log lists all changes between versions. - OUTPUTS - contains useful files, such as Bill of Materials (BOM), PDF of schematics, 3D .step file of the board and gerber files, organized by version.
Main components on the Simple sensor with easyC
Simple sensor with easyC bill of materials (BOM)
18 components, 11 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATTINY404-SSNR | SOIC-14 | U1 |
| 4 | HOLE_3.2MM HOLE_3.2mm | HOLE_3.2mm | H1, H2, H3, H4 |
| 1 | JST-SH_2PIN_1MM_C145954 JST-SH_2pin_1mm_C145954 | JST-SH_2pin_1mm_C145954 | K1 |
| 1 | HEADER_MALE_2X1 | HEADER_MALE_2X1 | K2 |
| 2 | easyC-SMD | easyC-connector | K3, K5 |
| 1 | HEADER-UPDI | HEADER-UPDI | K4 |
| 1 | DSHP03TS-S | DSHP03TS-S | K6 |
| 1 | purple | 0402LED | D1 |
| 2 | 0.1UF 0.1uF | 0603C | C1, C2 |
| 3 | 10K 10k | 0603R | R1, R3, R4 |
| 1 | 2K2 2k2 | 0402R | R2 |
Simple sensor with easyC design files
The KiCad project lives in the test-gh-syncer2/Soldered-Simple-sensor-with-easyC-breakout-hardware-design repository on GitHub; these links point at the commit this page was built from.
Simple sensor with easyC: common questions
What microcontroller does the Simple sensor with easyC use?
The Simple sensor with easyC is built around the ATTINY404-SSNR, from the AVR/Arduino family.
How big is the Simple sensor with easyC PCB?
The Simple sensor with easyC measures 38 × 22 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Simple sensor with easyC?
18 components, from 11 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Simple sensor with easyC design files?
From the test-gh-syncer2/Soldered-Simple-sensor-with-easyC-breakout-hardware-design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Simple sensor with easyC design in my own project?
Yes, under the terms of its TAPR-OHL-1.0 license, which test-gh-syncer2 chose for the repository.
Can I test firmware for the Simple sensor with easyC without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in Soldered-Simple-sensor-with-easyC-breakout-hardware-design
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k