Confined space gas monitor

ThendralArulmani07·confined-space-gas-monitor·hardware/schematic/worker_unit.kicad_sch

This repository ships a schematic but no board layout.

About the Confined space gas monitor PCB

Confined space gas monitor is an open source ESP32 PCB design by ThendralArulmani07, published on GitHub under the MIT license. It is a board, with 20 components from 18 distinct parts.

Its main chip is the ESP32 DevKit (ESP32-WROOM-32), from the ESP32 family. Other key parts include the 0.96in OLED SSD1306 I2C (addr 0x3C assumed), MQ-4 methane module (analog out, 5V heater), TP4056 charger w/ protection (USB) and MT3608 boost 3.7V->5V (set output to 5.0V). By type, the board carries 7 ICs, 7 resistors, 2 diodes, 1 transistor, 1 battery holder and 1 buzzer.

It belongs with the sensors, power & battery and iot & wireless designs in this gallery.

From the project

Work-in-progress ESP32-based confined-space gas safety monitor for sanitation workers (Viswakarma Awards 2026-27). You can also add topics such as esp32, gas-sensor, worker-safety and kicad.

More detail: docs/systemarchitecture.md, docs/workingprinciple.md.

There is no software/ or hardware/pcb/ folder: the proposal describes a wired prototype and a future mobile app, so neither has been created yet.

Main components on the Confined space gas monitor

ESP32 DevKit (ESP32-WROOM-32)0.96in OLED SSD1306 I2C (addr 0x3C assumed)MQ-4 methane module (analog out, 5V heater)TP4056 charger w/ protection (USB)MT3608 boost 3.7V->5V (set output to 5.0V)

Confined space gas monitor bill of materials (BOM)

20 components, 18 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32 DevKit (ESP32-WROOM-32)
U1
1
0.96in OLED SSD1306 I2C (addr 0x3C assumed)
U2
1
Electrochemical O2 module I2C (e.g. DFRobot Gravity; addr 0x73 assumed)
U3
1
Electrochemical H2S module I2C (part no. TO VERIFY; addr 0x74 assumed)
U4
1
MQ-4 methane module (analog out, 5V heater)
U5
1
TP4056 charger w/ protection (USB)
U6
1
MT3608 boost 3.7V->5V (set output to 5.0V)
U7
1
NPN BC547 (buzzer driver)
Q1
1
18650 cell + holder
BT1
1
Active buzzer 5V
BZ1
1
EMERGENCY push-button (NO)
SW1
1
Red LED
D1
1
Green LED
D2
2
330R
R1, R2
1
1k (base resistor)
R3
1
10k (MQ-4 divider top)
R4
1
15k (MQ-4 divider bottom)
R5
2
100k (Vbat divider)
R6, R7

Confined space gas monitor design files

The KiCad project lives in the ThendralArulmani07/confined-space-gas-monitor repository on GitHub; these links point at the commit this page was built from.

Confined space gas monitor: common questions

What microcontroller does the Confined space gas monitor use?

The Confined space gas monitor is built around the ESP32 DevKit (ESP32-WROOM-32), from the ESP32 family.

How many components are on the Confined space gas monitor?

20 components, from 18 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Confined space gas monitor design files?

From the ThendralArulmani07/confined-space-gas-monitor repository on GitHub, which has the schematic and the BOM; the links under Design files point to each one.

Can I use the Confined space gas monitor design in my own project?

Yes, under the terms of its MIT license, which ThendralArulmani07 chose for the repository.

Can I test firmware for the Confined space gas monitor without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards