WetProgrammer
timChase98·WetAvrProgrammer
About the WetProgrammer PCB
WetProgrammer is an open source AVR/Arduino PCB design by timChase98, published on GitHub. It is a 2-layer board measuring 48 × 25 mm, with 31 components from 17 distinct parts.
Its main chip is the ATmega32U4-AU, from the AVR/Arduino family. Other key parts include the TLV1117-33. By type, the board carries 11 resistors, 9 capacitors, 3 connectors, 2 ICs, 2 switches and 1 crystal.
Main components on the WetProgrammer
WetProgrammer bill of materials (BOM)
31 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATmega32U4-AU | TQFP-44_10x10mm_P0.8mm | U1 |
| 1 | TLV1117-33 | SOT-223-3_TabPin2 | U2 |
| 1 | 16MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | USB_B_Micro | usbMicro | J1 |
| 1 | AVR-ISP-6 | PinHeader_2x03_P2.54mm_Vertical | J2 |
| 1 | Conn_01x03_Male | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | 500mA | R_0805_2012Metric | F1 |
| 1 | AVR-ISP-10 | PinHeader_2x05_P1.27mm_Vertical | JPROG1 |
| 2 | SW_SPDT | 388Switch | SW1, SW2 |
| 1 | LED | LED_0805_2012Metric | D1 |
| 2 | 18pF | C_0805_2012Metric | C1, C2 |
| 4 | 100nF | C_0805_2012Metric | C3, C5, C6, C9 |
| 1 | 1uF | C_0805_2012Metric | C4 |
| 2 | 10uF | C_0805_2012Metric | C7, C8 |
| 2 | 22 | R_0805_2012Metric | R1, R2 |
| 2 | 4k7 | R_0805_2012Metric | R3, R5 |
| 7 | 330 | R_0805_2012Metric | R4, R6, R7, R8, R9, R10, R11 |
WetProgrammer design files
The KiCad project lives in the timChase98/WetAvrProgrammer repository on GitHub; these links point at the commit this page was built from.
- LayoutWetProgrammer.kicad_pcb
WetProgrammer: common questions
What microcontroller does the WetProgrammer use?
The WetProgrammer is built around the ATmega32U4-AU, from the AVR/Arduino family.
How big is the WetProgrammer PCB?
The WetProgrammer measures 48 × 25 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the WetProgrammer?
31 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the WetProgrammer design files?
From the timChase98/WetAvrProgrammer repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the WetProgrammer design in my own project?
The repository has no license, so all rights stay with timChase98. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the WetProgrammer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in WetAvrProgrammer
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k