Pqa
tio-checo·pqa·hw/pqa/pqa.kicad_pcb
About the Pqa PCB
Pqa is an open source ESP32 PCB design by tio-checo, published on GitHub. It is a 2-layer board measuring 113 × 87.3 mm, with 94 components from 23 distinct parts.
Its main chip is the ESP32-S3-Dev-Kit-NXR8, from the ESP32 family. Other key parts include the MCP3913-SS and TS1117BCW33. By type, the board carries 34 resistors, 30 capacitors, 13 diodes, 6 connectors, 4 ICs and 2 test points.
From the project
Power quality analyzer
Main components on the Pqa
Pqa bill of materials (BOM)
94 components, 23 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-Dev-Kit-NXR8 | ESP32-S3-Dev-Kit-NXR8 | U1 |
| 1 | MCP3913-SS | SSOP-28_5.3x10.2mm_P0.65mm_12mil | U2 |
| 2 | TS1117BCW33 | SOT-223-3_TabPin2 | U3, U4 |
| 1 | 4194304 | Crystal_HC49-U_Vertical | Y1 |
| 3 | AudioJack3_SwitchTR | Jack_3.5mm_ST214-C_Horizontal | J1, J2, J3 |
| 3 | ARK1x2 | TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J4, J5, J6 |
| 3 | Varistor | RV_Disc_D9mm_W3.5mm_P5mm | RV1, RV2, RV3 |
| 1 | GND | PinHeader_1x02_P2.54mm_Vertical | TP1 |
| 1 | DBG | PinHeader_1x02_P2.54mm_Vertical | TP2 |
| 1 | LED | LED_D3.0mm | D1 |
| 12 | LL4148 | D_MiniMELF | D2, D3, D4, D5, D6, D7, D8, D9 +4 |
| 1 | BLM21AG121SN1D Murata | L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L1 |
| 7 | 10uF/10V | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C16, C18, C20, C22, C28, C29 |
| 2 | 15pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3 |
| 21 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5, C6, C7, C8, C9, C10, C11 +13 |
| 4 | 100R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4 |
| 1 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 8 | 1k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R26, R27, R28, R29, R30, R31, R34 |
| 1 | 1M | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 9 | 100k | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R8, R9, R10, R13, R14, R15, R18, R19 +1 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 6 | 470R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R12, R16, R17, R21, R22 |
| 3 | 100k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R23, R24, R25 |
| 2 | 10R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R32, R33 |
Pqa design files
The KiCad project lives in the tio-checo/pqa repository on GitHub; these links point at the commit this page was built from.
- Layouthw/pqa/pqa.kicad_pcb
- Schematichw/pqa/pqa.kicad_sch
Pqa: common questions
What microcontroller does the Pqa use?
The Pqa is built around the ESP32-S3-Dev-Kit-NXR8, from the ESP32 family.
How big is the Pqa PCB?
The Pqa measures 113 × 87.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pqa?
94 components, from 23 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pqa design files?
From the tio-checo/pqa repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Pqa design in my own project?
The repository has no license, so all rights stay with tio-checo. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Pqa without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k