Business-Card
TomasD-git·Business-Card·bussines card/bussines card.kicad_pcb
About the Business-Card PCB
Business-Card is an open source STM32 PCB design by TomasD-git, published on GitHub. It is a 2-layer board measuring 105.9 × 61.4 mm, with 36 components from 20 distinct parts.
Its main chip is the STM32F072C8TX, from the STM32 family. Other key parts include the NT3H2111W0FHKH and AP2112K-3.3. By type, the board carries 13 capacitors, 10 resistors, 6 connectors, 3 ICs, 2 diodes and 1 inductor.
It belongs with the displays & leds and dev boards & breakouts designs in this gallery.
From the project
Basically a custom devboard inside a bussines card that has nfc and e-paper
- E-paper display — Configure once image stays - NFC — tap to share Contact info, a URL, or any custom NFC - 16 exposed GPIO pins — Connector makes it easy to use for another project - No power design - Once flashed and configured, nfc works with no external power and image stays on e-paper screen
The Business Card is a fully custom PCB designed. The microcontroller drives both the e-paper display and the NFC IC over SPI/I2C, while the 16 GPIO pins are broken out along one edge for easy prototyping.
Main components on the Business-Card
Business-Card bill of materials (BOM)
36 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | NT3H2111W0FHKH | QFN8P50_160X160X50L40X20N | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | STM32F072C8TX STM32F072C8Tx | LQFP-48_7x7mm_P0.5mm | U3 |
| 2 | CONN_01X04_PIN Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J2, J3 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 2 | CONN_01X10_SOCKET Conn_01x10_Socket | PinSocket_1x10_P2.54mm_Vertical | J5, J6 |
| 1 | USB_C_RECEPTACLE_USB2.0_16P USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_XKB_U262-16XN-4BVC11 | J7 |
| 1 | SW_Push | SW_Push_1P1T_XKB_TS-1187A | BOOT0 |
| 1 | GREEN LED | LED_0402_1005Metric | D1 |
| 1 | BLUE LED | LED_0402_1005Metric | D2 |
| 1 | L | COIL_GENERATOR | L1 |
| 3 | 1UF 1uf | C_0402_1005Metric | C1, C3, C9 |
| 7 | 100NF 100nF | C_0402_1005Metric | C2, C4, C5, C7, C8, C12, C13 |
| 3 | 10UF 10uf | C_0603_1608Metric | C6, C10, C11 |
| 2 | 5.1K | R_0402_1005Metric | R1, R2 |
| 2 | 22 | R_0402_1005Metric | R3, R4 |
| 2 | 10K | R_0402_1005Metric | R5, R8 |
| 2 | 4.7K | R_0402_1005Metric | R6, R7 |
| 1 | 330 | R_0402_1005Metric | R11 |
| 1 | 68 | R_0402_1005Metric | R12 |
Business-Card design files
The KiCad project lives in the TomasD-git/Business-Card repository on GitHub; these links point at the commit this page was built from.
Business-Card: common questions
What microcontroller does the Business-Card use?
The Business-Card is built around the STM32F072C8TX, from the STM32 family.
How big is the Business-Card PCB?
The Business-Card measures 105.9 × 61.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Business-Card?
36 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Business-Card design files?
From the TomasD-git/Business-Card repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Business-Card design in my own project?
The repository has no license, so all rights stay with TomasD-git. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Business-Card without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k