Squidgrip
unixvoid·squidgrip·hardware/squidgrip.kicad_pcb
About the Squidgrip PCB
Squidgrip is an open source PCB design by unixvoid, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 42.8 × 19 mm, with 21 components from 15 distinct parts.
Other key parts include the C969151, C110150 and C2868428. By type, the board carries 8 resistors, 3 ICs, 3 diodes, 3 capacitors, 2 switches and 1 connector.
It belongs with the usb & debug tools designs in this gallery.
From the project
squidgrip auto-reset ESP32 flasher based on a CP2102N
Squidgrip is a clamp-on USB-UART probe for programming ESP32 boards. It is a CP2102N on a small USB-C board with a 6-pin pogo pin array on a thin tongue, plus a 3D printed clamp that presses that tongue onto the programming pads of a target board.
It carries the ESP32 auto-reset circuit, so esptool, the ExpressLRS Configurator, PlatformIO, Arduino IDE, etc can drop a target into the bootloader and flash it without you touching anything. There are RESET and BOOT buttons for doing it by hand, power/TX/RX LEDs, and a 3.3 V LDO so the probe can power the board it is flashing.

Main components on the Squidgrip
Squidgrip bill of materials (BOM)
21 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C969151 CP2102N-Axx-xQFN24 | QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U1 |
| 1 | C110150 MBT3904DW1T1G | SOT236 | U2 |
| 1 | C2868428 TLV75733PDRVR | TLV75733PDRVR | U3 |
| 1 | 2171790001 | MOLEX_2171790001 | J1 |
| 2 | PTS526 SM15 SMTR2 LFS | GSPTS004901 | SW1, SW2 |
| 1 | SQUIDGRIP | Untitled | SG1 |
| 1 | YLW | LED_0805_2012Metric | D1 |
| 1 | GRN | LED_0805_2012Metric | D2 |
| 1 | BLUE | LED_0805_2012Metric | D3 |
| 1 | C1779 4.7uF | C_0805_2012Metric | C1 |
| 2 | C1711 .1uF | C_0805_2012Metric | C2, C3 |
| 2 | C17414 10k | R_0805_2012Metric | R1, R8 |
| 1 | C17513 1k | R_0805_2012Metric | R5 |
| 2 | C27834 5.1k | R_0805_2012Metric | R6, R7 |
| 3 | C17520 2.2k | R_0805_2012Metric | R9, R10, R11 |
Squidgrip design files
The KiCad project lives in the unixvoid/squidgrip repository on GitHub; these links point at the commit this page was built from.
Squidgrip: common questions
How big is the Squidgrip PCB?
The Squidgrip measures 42.8 × 19 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Squidgrip?
21 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Squidgrip design files?
From the unixvoid/squidgrip repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Squidgrip design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which unixvoid chose for the repository.
Similar boards
USB Hub Test
osy
50 × 50 mm85 parts4LCC-BY-4.0703XG Station Power
osy
54.3 × 91 mm9 parts2LCC-BY-4.0703FW-EC-DongleHiderPlus
LeoDJ
28.2 × 26.1 mm14 parts4LCERN-OHL-W-2.0497Adapter tsop48
bbogush
48 × 33 mm3 parts2LGPL-3.0389Adapter tsop48 solder
bbogush
48 × 33 mm3 parts2LGPL-3.0389Adapter soic8 solder
bbogush
48 × 20 mm3 parts2LGPL-3.0389