13 open source boards using the C969151

Real designs built with the C969151, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

13 boardsClear filters|Most starred

How designs wire the C969151

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the C969151 connects to, and the resistors, capacitors and other passives placed on it.

  • The WAKEUP/GPIO.3 pin is left unconnected on 6 of 6 designs.
  • The SUSPEND pins is left unconnected on 100% of them.
  • The CTS pin is left unconnected on 6 of 6 designs.
  • The DSR pin is left unconnected on 6 of 6 designs.
RI/CLKpin 1Connected to: Not connected 71%
GNDpin 2, 25Connected to: GND 69% · not connected 23%
VIOpin 5Connected to: Signal 50% · not connected 33% · 3.3V 17%
  • Capacitor to GND on 50% · 100 nF (2), 4.7 µF (2), 1 µF (1)
VDDpin 6Connected to: Signal 50% · not connected 33% · 3.3V 17%
  • Capacitor to GND on 50% · 100 nF (3), 4.7 µF (2), 1 µF (1)
VREGINpin 7Connected to: VBUS 67% · a signal 33%
  • Decoupling capacitor on 50% · 100 nF (3), 4.7 µF (2)
RSTpin 9Connected to: Not connected 67% · a signal 33%
NCpin 10, 16Connected to: Not connected 92%
WAKEUP/GPIO.3pin 11Connected to: Not connected 100%
RS485/GPIO.2pin 12Connected to: Not connected 83% · a signal 17%
SUSPENDpin 15, 17Connected to: Not connected 100%
CTSpin 18Connected to: Not connected 100%
RTSpin 19Connected to: Signal 67% · not connected 17% · 5V 17%
  • Series resistor on 67% · 10 kΩ (4)
DSRpin 22Connected to: Not connected 100%
DTRpin 23Connected to: Signal 100%
  • Series resistor on 67% · 10 kΩ (4)
DCDpin 24Connected to: Not connected 83% · a signal 17%

7 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Apple 68k FujiNet by FujiNetWIFI, Programmer by benanderman, C3-27-epaper touch by martinberlin and Cinread-IT8951 S3 HAT by martinberlin.

The C969151 in open source designs

The gallery holds 13 open source boards using the C969151 from 7 GitHub repositories; a typical one measures about 83.2 × 59.9 mm and carries around 46 components.

77% are two-layer designs, the rest use four layers or more, and 77% carry an open source license.

The most starred is FujiApple DevKit Combo by FujiNetWIFI.

Parts used alongside the C969151

Microcontrollers on boards using the C969151

C969151: common questions

Where can I find a C969151 reference design?

Each of the 13 boards on this page is a real design using the C969151. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the C969151 WAKEUP/GPIO.3 pin connected?

The WAKEUP/GPIO.3 pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 7 open source designs using the C969151.

How is the C969151 SUSPEND pin connected?

The SUSPEND pins is left unconnected on 100% of them. Counted from the KiCad layouts of 7 open source designs using the C969151.

How is the C969151 CTS pin connected?

The CTS pin is left unconnected on 6 of 6 designs. Counted from the KiCad layouts of 7 open source designs using the C969151.

Which microcontrollers do boards using the C969151 use?

Most are built on ESP32 (7), AVR/Arduino (1) and RP2040/RP2350 (1).

How big is a typical board using the C969151?

The median is 83.2 × 59.9 mm, and 77% are two-layer designs.

What is the most popular open source board using the C969151?

By GitHub stars, FujiApple DevKit Combo by FujiNetWIFI, with 138 stars.

Can I simulate one of these boards using the C969151 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part