AdvElectronicsBadge

UNSW-Makerspaces·AdvElectronicsBadge·hardware/PicoGamePad_indev.kicad_pcb

AdvElectronicsBadge PCB layout, top view — open source RP2040/RP2350 board by UNSW-Makerspaces

About the AdvElectronicsBadge PCB

AdvElectronicsBadge is an open source RP2040/RP2350 PCB design by UNSW-Makerspaces, published on GitHub. It is a 4-layer board measuring 68.9 × 37.6 mm, with 49 components from 33 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the ASM1117-3.3 and WQ25JVS. By type, the board carries 18 capacitors, 8 switches, 7 resistors, 6 test points, 3 ICs and 2 connectors.

Main components on the AdvElectronicsBadge

AdvElectronicsBadge bill of materials (BOM)

49 components, 33 distinct parts.

QtyPartRefs
1
ASM1117-3.3
U1
1
WQ25JVS
U3
1
RP2040
U4
1
X322512MMB4SI
Y1
1
C116159
J1
1
RBP_GPIO_CONN
J3
1
C261953
F1
1
1-0201FBV0T
Conn_01x02
TAD
JP1
1
LL1009-2A, 2.54MM 2*3PIN HEADER,LENGTH=20MM
Conn_02x03
Cixi Langlin
JP2
1
DOWN
SW1
1
START
SW2
1
LEFT
SW3
1
B
SW4
1
UP
SW5
1
A
SW6
1
RIGHT
SW7
1
SELECT
SW8
1
MCU 3v3
TP1
1
MCU 1v2
TP2
1
LED DATA
TP5
Show 13 more
QtyPartRefs
1
VBUS
TP8
1
LDO_{VOUT}
TP9
1
LDO_{VIN}
TP10
1
WS2812B
LED1
4
1μF
C1, C4, C8, C11
2
10μF
C2, C3
2
14pF
C5, C6
10
100nF
C7, C9, C10, C12, C13, C14, C15, C16 +2
2
5.1kΩ
R1, R5
2
27Ω
R2, R3
1
R
R4
1
10kΩ
R6
1
1k?
R7

AdvElectronicsBadge design files

The KiCad project lives in the UNSW-Makerspaces/AdvElectronicsBadge repository on GitHub; these links point at the commit this page was built from.

AdvElectronicsBadge: common questions

What microcontroller does the AdvElectronicsBadge use?

The AdvElectronicsBadge is built around the RP2040, from the RP2040/RP2350 family.

How big is the AdvElectronicsBadge PCB?

The AdvElectronicsBadge measures 68.9 × 37.6 mm, has 4 copper layers and is 1.02 mm thick.

How many components are on the AdvElectronicsBadge?

49 components, from 33 distinct parts. The full bill of materials is listed on this page.

Where can I download the AdvElectronicsBadge design files?

From the UNSW-Makerspaces/AdvElectronicsBadge repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the AdvElectronicsBadge design in my own project?

The repository has no license, so all rights stay with UNSW-Makerspaces. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the AdvElectronicsBadge without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards