Pit Radio
About the Pit Radio PCB
Pit Radio is an open source ESP32 PCB design by UofA-BAJA, published on GitHub. It is a 2-layer board measuring 55.5 × 65.5 mm, with 3 components from 3 distinct parts.
Its main chip is the ESP32-DEVKITC-32D, from the ESP32 family. Other key parts include the E01-ML01DP5. By type, the board carries 1 IC and 1 connector.
It belongs with the rf & radio designs in this gallery.
From the project
The software behind the electrical system in Baja Wildcat Racing.
The software behind the electrical system in Baja Wildcat Racing.
This is the BAJA Wildcat Racing team for school year 2024-2025.
Check out the 'doc' (documentation) folder in order to get started!
Main components on the Pit Radio
Pit Radio bill of materials (BOM)
3 components, 3 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | E01-ML01DP5 | Ebyte E01-ML01DP5 | U2 |
| 1 | Conn_01x02 | SolderWire-0.75sqmm_1x02_P4.8mm_D1.25mm_OD2.3mm | J1 |
| 1 | ESP32-DEVKITC-32D | MODULE_ESP32-DEVKITC-32D | UNIT_1 |
Pit Radio design files
The KiCad project lives in the UofA-BAJA/2024-2025-Firmware repository on GitHub; these links point at the commit this page was built from.
Pit Radio: common questions
What microcontroller does the Pit Radio use?
The Pit Radio is built around the ESP32-DEVKITC-32D, from the ESP32 family.
How big is the Pit Radio PCB?
The Pit Radio measures 55.5 × 65.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pit Radio?
3 components, from 3 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pit Radio design files?
From the UofA-BAJA/2024-2025-Firmware repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Pit Radio design in my own project?
The repository has no license, so all rights stay with UofA-BAJA. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Pit Radio without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in 2024-2025-Firmware
Raspberry PiCM5IO
160 × 90 mm62 parts4LNo license6
ESP32Dash
106 × 105.1 mm33 parts2LNo license6
Power Regulator PCB (LT8608)
77.5 × 70.5 mm33 parts2LNo license6
AVR/ArduinoTachometer
80 × 85 mm24 parts2LNo license6
AVR/ArduinoBaja Speedometer
104.4 × 46.4 mm23 parts2LNo license6
ESP32Dash Main
137.9 × 76.2 mm18 parts2LNo license6
Dash Indicators (Right)
55.8 × 87 mm18 parts2LNo license6
Dash Indicators (Left)
55.8 × 87 mm18 parts2LNo license6
Power Regulator PCB (AZ1084C)
48 × 29 mm11 parts2LNo license6
Main Computer
55.5 × 65.5 mm5 parts2LNo license6
12 to 5 with Trimmer
64.8 × 53 mm3 parts2LNo license6
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k