Modulo USB
vecchiettidaniel·caja-negra·proyecto-td2-2017/Esquematicos/Modulo_USB/Modulo_USB.kicad_pcb
About the Modulo USB PCB
Modulo USB is an open source NXP PCB design by vecchiettidaniel, published on GitHub. It is a 2-layer board measuring 49.5 × 92.7 mm, with 16 components from 15 distinct parts.
Its main chip is the LPC1769-54Pines, from the NXP family. Other key parts include the RegLin-G-O-I and MAX485. By type, the board carries 6 resistors, 3 connectors, 3 capacitors and 2 ICs.
Main components on the Modulo USB
Modulo USB bill of materials (BOM)
16 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RegLin-G-O-I | TO-220_Neutral123_Vertical | U101 |
| 1 | MAX485 | DIP-8_W7.62mm_LongPads | U102 |
| 1 | USB_B | USB-pads | P101 |
| 1 | WG12864A-GLCD | Pin_Header_Straight_1x20 | P102 |
| 1 | RS485 | Pin_Header_Straight_1x02 | P103 |
| 1 | LPC1769-54Pines | LPC1769_Stick-54-pins | LPC1769-N101 |
| 1 | GLCD-15k | Potentiometer_Bourns_3296W_3-8Zoll_Inline_ScrewUp | RV101 |
| 1 | GLCD-100uF | C_Radial_D5_L11_P2 | C101 |
| 1 | USB-100uF | C_Radial_D5_L11_P2 | C102 |
| 1 | Reg-100uF | C_Radial_D5_L11_P2 | C103 |
| 2 | GLCD-10K | R3 | R101, R102 |
| 1 | USB-R1-1k | R3 | R103 |
| 1 | GLCD-100 | R3 | R104 |
| 1 | USB-R2-5k | R3 | R105 |
| 1 | RS485-120 | R3 | R106 |
Modulo USB design files
The KiCad project lives in the vecchiettidaniel/caja-negra repository on GitHub; these links point at the commit this page was built from.
Modulo USB: common questions
What microcontroller does the Modulo USB use?
The Modulo USB is built around the LPC1769-54Pines, from the NXP family.
How big is the Modulo USB PCB?
The Modulo USB measures 49.5 × 92.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Modulo USB?
16 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the Modulo USB design files?
From the vecchiettidaniel/caja-negra repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Modulo USB design in my own project?
The repository has no license, so all rights stay with vecchiettidaniel. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Modulo USB without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
More boards in caja-negra
Similar boards
NXP
32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763NXP
Mega-Cube-Board
MaltWhiskey
200 × 54 mm100 parts4LNo license763NXP
MCL6809
MicroCoreLabs
32.3 × 61 mm7 parts4LNo license532NXP
MCL68
MicroCoreLabs
31.6 × 84.1 mm13 parts4LNo license532NXP
MCL65+
MicroCoreLabs
72.6 × 64.1 mm6 parts2LNo license532NXP
MCLZ8
MicroCoreLabs
37.1 × 61.5 mm6 parts4LNo license532