18 open source boards using the MAX485

Real designs built with the MAX485, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

18 boardsClear filters|Most starred

How designs wire the MAX485

Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the MAX485 connects to, and the resistors, capacitors and other passives placed on it.

  • The B pin has a series resistor on 9 of 12 designs, most often 120 Ω (then 0 Ω).
  • The A pin has a series resistor on 8 of 12 designs, most often 120 Ω (then 0 Ω).
  • The VCC pin has a decoupling capacitor on 6 of 12 designs, most often 100 nF (then 4.7 µF).
  • The A pin has a pull-up to 5V on 5 of 12 designs, most often 20 kΩ (then 4.7 kΩ).
REpin 2Connected to: The microcontroller 25% · 5V 17%
  • Pull-up to 5V on 33% · 10 kΩ (3), 470 Ω (1), 4.7 kΩ (1)
DEpin 3Connected to: The microcontroller 25%
  • Pull-up to 5V on 33% · 10 kΩ (3), 470 Ω (1), 4.7 kΩ (1)
GNDpin 5Connected to: GND 92%
Apin 6Connected to: A connector 83%
  • Series resistor on 67% · 120 Ω (7), 0 Ω (1)
  • Pull-up to 5V on 42% · 20 kΩ (2), 4.7 kΩ (1), 10 kΩ (1)
Bpin 7Connected to: A connector 83%
  • Series resistor on 75% · 120 Ω (8), 0 Ω (1)
  • Resistor to GND on 42% · 20 kΩ (2), 4.7 kΩ (1), 10 kΩ (1)
VCCpin 8Connected to: 5V 92%
  • Decoupling capacitor on 50% · 100 nF (6), 4.7 µF (1), 10 µF (1)

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pcb rs485 by HydroVinci-PULV, Timer-RTC-STM32-Tm1638 by nhantt92, Lasersaurv2 by bullestock and Plant Partner PCB 1.0 by aboler.

The MAX485 in open source designs

The gallery holds 18 open source boards using the MAX485 from 13 GitHub repositories; a typical one measures about 86.4 × 72.2 mm and carries around 67 components.

94% are two-layer designs, the rest use four layers or more, and 22% carry an open source license.

The most starred is Pcb rs485 by HydroVinci-PULV.

Microcontrollers on boards using the MAX485

MAX485: common questions

Where can I find a MAX485 reference design?

Each of the 18 boards on this page is a real design using the MAX485. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the MAX485 B pin?

The B pin has a series resistor on 9 of 12 designs, most often 120 Ω (then 0 Ω). Counted from the KiCad layouts of 12 open source designs using the MAX485.

What resistor goes on the MAX485 A pin?

The A pin has a series resistor on 8 of 12 designs, most often 120 Ω (then 0 Ω). Counted from the KiCad layouts of 12 open source designs using the MAX485.

What decoupling capacitors do designs use on the MAX485 VCC pin?

The VCC pin has a decoupling capacitor on 6 of 12 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 12 open source designs using the MAX485.

What parts are used alongside the MAX485?

The L7805, 4011, CNY17-1, LM358 and MSGEQ7 appear in the most repositories here.

Which microcontrollers do boards using the MAX485 use?

Most are built on ESP32 (3), NXP (2), PIC (2) and STM32 (2).

How big is a typical board using the MAX485?

The median is 86.4 × 72.2 mm, and 94% are two-layer designs.

What is the most popular open source board using the MAX485?

By GitHub stars, Pcb rs485 by HydroVinci-PULV, with 11 stars.

Can I simulate one of these boards using the MAX485 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part