Servo-Tester
VX7FAR·Servo-Tester·PCB/servo tester.kicad_pcb
About the Servo-Tester PCB
Servo-Tester is an open source AVR/Arduino PCB design by VX7FAR, published on GitHub. It is a 2-layer board measuring 113 × 62.5 mm, with 21 components from 9 distinct parts.
Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the ER_OLEDM0.91_1x-I2C. By type, the board carries 9 switches, 2 diodes, 1 IC and 1 module.
It belongs with the robotics & motion and displays & leds designs in this gallery.
From the project
A servo tester is basically a device someone can use to check whether their servo motors work or not and this can be very essential as it can help you to check your servo motors before having to write new code just to run a single servo. Most of the servo need 1ms to 2ms pulse so
A servo tester is basically a device someone can use to check whether their servo motors work or not and this can be very essential as it can help you to check your servo motors before having to write new code just to run a single servo. Most of the servo need 1ms to 2ms pulse so that it moves from 0 to 180 degrees respectively.
The main component here is Arduino Nano I chose this specially because this servo tester also has a 0.91 inch display module. The display shows stats like speed, angle, mode, etc. It also feature a potentiometer to control different things based on the mode selected…
Main components on the Servo-Tester
Servo-Tester bill of materials (BOM)
21 components, 9 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ER_OLEDM0.91_1x-I2C | ER_OLEDM0.91_1x-I2C | U1 |
| 1 | Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 2 | TestPoint | SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | +B1, -B1 |
| 1 | R_Potentiometer | Potentiometer_Bourns_3386C_Horizontal | B10K1 |
| 2 | SW_Push | SW_PUSH_6mm | MODE1, RESET1 |
| 9 | Conn_01x01_Pin | PinHeader_1x01_P2.54mm_Horizontal | S1-G1, S1-P1, S1-S1, S2-G1, S2-P1, S2-S1, S3-G1, S3-P1 +1 |
| 2 | Conn_01x01_Pin | PinHeader_1x01_P2.54mm_Horizontal | SB-GND1, SB-VCC1 |
| 1 | SW_Push | SW_DIP_SPSTx01_Slide_9.78x4.72mm_W7.62mm_P2.54mm | SW_MAIN1 |
| 2 | D | D_A-405_P10.16mm_Horizontal | D4, D5 |
Servo-Tester design files
The KiCad project lives in the VX7FAR/Servo-Tester repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/servo tester.kicad_pcb
- SchematicPCB/servo tester.kicad_sch
Servo-Tester: common questions
What microcontroller does the Servo-Tester use?
The Servo-Tester is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.
How big is the Servo-Tester PCB?
The Servo-Tester measures 113 × 62.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Servo-Tester?
21 components, from 9 distinct parts. The full bill of materials is listed on this page.
Where can I download the Servo-Tester design files?
From the VX7FAR/Servo-Tester repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Servo-Tester design in my own project?
The repository has no license, so all rights stay with VX7FAR. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Servo-Tester without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k