PCB-Design-MCU-Datalogger-
Warik1206·PCB-Design-MCU-Datalogger-
About the PCB-Design-MCU-Datalogger-
PCB-Design-MCU-Datalogger- is an open source AVR/Arduino PCB design by Warik1206, published on GitHub. It is a 2-layer board measuring 50.8 × 30.5 mm, with 25 components from 16 distinct parts.
Its main chip is the ATMEGA328P-AN, from the AVR/Arduino family. Other key parts include the 24LC1025 and DS1337S_. By type, the board carries 7 resistors, 5 capacitors, 4 ICs, 4 connectors, 2 crystals and 2 diodes.
Main components on the PCB-Design-MCU-Datalogger-
PCB-Design-MCU-Datalogger- bill of materials (BOM)
25 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 24LC1025 | SOIC-8_5.23x5.23mm_P1.27mm | U1, U2 |
| 1 | DS1337S_ | SOIC127P600X175-8N | U3 |
| 1 | ATMEGA328P-AN | QFP80P900X900X120-32N | U4 |
| 1 | 16 MHz | Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | 32.768 KHz | Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y2 |
| 2 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J1, J2 |
| 1 | Conn_01x09_Pin | PinHeader_1x09_P2.54mm_Vertical | J3 |
| 1 | Conn_02x03_Odd_Even | PinHeader_2x03_P2.54mm_Vertical | J4 |
| 1 | Battery | PinHeader_1x02_P2.54mm_Vertical | BT1 |
| 2 | LED | LED_0805_2012Metric | D1, D2 |
| 2 | 0.1uF | C_0805_2012Metric | C1, C2 |
| 2 | 22pF | C_0805_2012Metric | C3, C4 |
| 1 | 100nF | C_0805_2012Metric | C5 |
| 2 | 330 | R_0805_2012Metric | R1, R4 |
| 2 | 4.7K | R_0805_2012Metric | R2, R5 |
| 3 | 10K | R_0805_2012Metric | R3, R6, R7 |
PCB-Design-MCU-Datalogger- design files
The KiCad project lives in the Warik1206/PCB-Design-MCU-Datalogger- repository on GitHub; these links point at the commit this page was built from.
- LayoutMCU_Datalogger.kicad_pcb
- SchematicMCU_Datalogger.kicad_sch
PCB-Design-MCU-Datalogger-: common questions
What microcontroller does the PCB-Design-MCU-Datalogger- use?
The PCB-Design-MCU-Datalogger- is built around the ATMEGA328P-AN, from the AVR/Arduino family.
How big is the PCB-Design-MCU-Datalogger-?
The PCB-Design-MCU-Datalogger- measures 50.8 × 30.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the PCB-Design-MCU-Datalogger-?
25 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the PCB-Design-MCU-Datalogger- design files?
From the Warik1206/PCB-Design-MCU-Datalogger- repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the PCB-Design-MCU-Datalogger- design in my own project?
The repository has no license, so all rights stay with Warik1206. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the PCB-Design-MCU-Datalogger- without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k