30 open source boards using the DS1337S_

Real designs built with the DS1337S_, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

30 boardsClear filters|Most starred

How designs wire the DS1337S_

Read from the KiCad layouts of 28 open source designs, one per repository: what each pin of the DS1337S_ connects to, and the resistors, capacitors and other passives placed on it.

  • The SDA pin has a pull-up to VCC on 28 of 28 designs, most often 4.7 kΩ.
  • The SCL pin has a pull-up to VCC on 28 of 28 designs, most often 4.7 kΩ.
  • The X1 pin has a crystal on 27 of 28 designs, most often 32.768 kHz (then 37.768 kHz).
  • The X2 pin has a crystal on 27 of 28 designs, most often 32.768 kHz (then 37.768 kHz).
X1pin 1Connected to: Signal 96%
  • Crystal on 96% · 32.768 kHz (25), 37.768 kHz (1)
X2pin 2Connected to: Signal 96%
  • Crystal on 96% · 32.768 kHz (25), 37.768 kHz (1)
INTApin 3Connected to: Signal 96%
  • Pull-up to VCC on 93% · 10 kΩ (25)
GNDpin 4Connected to: GND 100%
SDApin 5Connected to: 24LC1025 100%, a connector 96%, the microcontroller 96%
  • Pull-up to VCC on 100% · 4.7 kΩ (27)
SCLpin 6Connected to: 24LC1025 100%, a connector 96%, the microcontroller 96%
  • Pull-up to VCC on 100% · 4.7 kΩ (27)
SQW/~INTpin 7Connected to: Signal 96%
  • Pull-up to VCC on 93% · 10 kΩ (25)
VCCpin 8Connected to: VCC 96%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MCU Data Logger by AhmedAbo-Eita, DataLogger-Board by DevMajed, Data Logger by Shourya-x and ATMEGA328P-AU Data-Logger by pushtiujeniya.

The DS1337S_ in open source designs

The gallery holds 30 open source boards using the DS1337S_ from 28 GitHub repositories; a typical one measures about 50.8 × 33.5 mm and carries around 25 components.

57% are two-layer designs, the rest use four layers or more, and 13% carry an open source license.

The most starred is Data Logger by Shourya-x.

Parts used alongside the DS1337S_

Microcontrollers on boards using the DS1337S_

DS1337S_: common questions

Where can I find a DS1337S_ reference design?

Each of the 30 boards on this page is a real design using the DS1337S_. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the DS1337S_ SDA pin?

The SDA pin has a pull-up to VCC on 28 of 28 designs, most often 4.7 kΩ. Counted from the KiCad layouts of 28 open source designs using the DS1337S_.

What pull-up resistor is used on the DS1337S_ SCL pin?

The SCL pin has a pull-up to VCC on 28 of 28 designs, most often 4.7 kΩ. Counted from the KiCad layouts of 28 open source designs using the DS1337S_.

How is the DS1337S_ X1 pin connected?

The X1 pin has a crystal on 27 of 28 designs, most often 32.768 kHz (then 37.768 kHz). Counted from the KiCad layouts of 28 open source designs using the DS1337S_.

What parts are used alongside the DS1337S_?

The 24LC1025, ATMEGA328P-AU and ATMEGA328P-AN appear in the most repositories here.

Which microcontrollers do boards using the DS1337S_ use?

Most are built on AVR/Arduino (29) and ESP32 (1).

How big is a typical board using the DS1337S_?

The median is 50.8 × 33.5 mm, and 57% are two-layer designs.

What is the most popular open source board using the DS1337S_?

By GitHub stars, Data Logger by Shourya-x, with 3 stars.

Can I simulate one of these boards using the DS1337S_ before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part