47 open source boards using the 24LC1025

Real designs built with the 24LC1025, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

47 boardsClear filters|Most starred

How designs wire the 24LC1025

Read from the KiCad layouts of 40 open source designs, one per repository: what each pin of the 24LC1025 connects to, and the resistors, capacitors and other passives placed on it.

  • The SDA pin has a pull-up to VCC on 33 of 39 designs, most often 4.7 kΩ (then 10 kΩ).
  • The SCL pin has a pull-up to VCC on 33 of 39 designs, most often 4.7 kΩ (then 10 kΩ).
  • The WP pin is tied to GND on 38 of 39 designs.
  • The A2 pin is tied to VCC on 34 of 40 designs (GND on 2, a signal on 4).
A0pin 1Connected to: VCC 70% · GND 18%
A1pin 2Connected to: VCC 63% · GND 25%
A2pin 3Connected to: VCC 85%
GNDpin 4Connected to: GND 100%
SDApin 5Connected to: The microcontroller 97%, 24LC1025 82%, DS1337S_ 64%
  • Pull-up to VCC on 85% · 4.7 kΩ (28), 10 kΩ (1), 1 kΩ (1)
SCLpin 6Connected to: The microcontroller 97%, 24LC1025 82%, DS1337S_ 64%
  • Pull-up to VCC on 85% · 4.7 kΩ (28), 10 kΩ (1), 1 kΩ (1)
WPpin 7Connected to: GND 97%
VCCpin 8Connected to: VCC 95%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Nyan keys by portlandhodl, Arduino Battery Powered clone with extended EEPROM and clock by Ikarthikmb, Same70 by brengi and Arduino hat by AronAyub.

The 24LC1025 in open source designs

The gallery holds 47 open source boards using the 24LC1025 from 40 GitHub repositories; a typical one measures about 53 × 34.8 mm and carries around 25 components.

60% are two-layer designs, the rest use four layers or more, and 23% carry an open source license.

The most starred is Project by portlandhodl.

Microcontrollers on boards using the 24LC1025

24LC1025: common questions

Where can I find a 24LC1025 reference design?

Each of the 47 boards on this page is a real design using the 24LC1025. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What pull-up resistor is used on the 24LC1025 SDA pin?

The SDA pin has a pull-up to VCC on 33 of 39 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 40 open source designs using the 24LC1025.

What pull-up resistor is used on the 24LC1025 SCL pin?

The SCL pin has a pull-up to VCC on 33 of 39 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 40 open source designs using the 24LC1025.

How is the 24LC1025 WP pin connected?

The WP pin is tied to GND on 38 of 39 designs. Counted from the KiCad layouts of 40 open source designs using the 24LC1025.

What parts are used alongside the 24LC1025?

The DS1337S_, ATMEGA328P-AU, AMS1117-3.3, AMS1117-5.0 and ATMEGA328P-AN appear in the most repositories here.

Which microcontrollers do boards using the 24LC1025 use?

Most are built on AVR/Arduino (38), STM32 (4), ESP32 (1) and PIC (1).

How big is a typical board using the 24LC1025?

The median is 53 × 34.8 mm, and 60% are two-layer designs.

What is the most popular open source board using the 24LC1025?

By GitHub stars, Project by portlandhodl, with 96 stars.

Can I simulate one of these boards using the 24LC1025 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part