Mr Stash
Wireb·Mr_Stash·KiCad/Mr_Stash.kicad_pcb
About the Mr Stash PCB
Mr Stash is an open source PIC PCB design by Wireb, published on GitHub under the MIT license. It is a 2-layer board measuring 101.3 × 63.1 mm, with 62 components from 30 distinct parts.
Its main chip is the PIC16F15355-SSOP, from the PIC family. Other key parts include the TSSP58038. By type, the board carries 24 resistors, 7 diodes, 7 capacitors, 5 test points, 4 switches and 3 transistors.
It belongs with the wearables designs in this gallery.
From the project
DC26 Mr Stash badge design
NOTE I screwed up and wipped my laptop hard drive before pulling the final firmware version off it. The version in this repo is from right before I left for DC26 and is missing the following items: - LED mode that cycles though all patterns - Bonus hidden Morse code message at high pattern offset - All but one vibe pattern - Vibe mode that cycles though all patterns once - Updated touch sensor code. Code in repo works good in my house in MN but was unusable in the dry Nevada environment.
Main components on the Mr Stash
Mr Stash bill of materials (BOM)
62 components, 30 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | PIC16F15355-SSOP | SSOP-28_5.3x10.2mm_Pitch0.65mm | U1 |
| 1 | TSSP58038 | TSSP58038_custom_45_SMT | U2 |
| 2 | motor | Pager_motor_10mm_smt | M1, M2 |
| 3 | RK7002BMT116 | SOT-23 | Q1, Q2, Q3 |
| 1 | Badgelife_shitty_connector | Badgelife-Shitty-2x2 | X1 |
| 1 | Badge_bus | 10120045-40-LF | J2 |
| 1 | Select button | blank_button_7.5mm | B1 |
| 1 | Set button | blank_button_7.5mm | B2 |
| 1 | A button | blank_button_7.5mm | B3 |
| 1 | B button | blank_button_7.5mm | B4 |
| 1 | Battery | Keystone_3_AA_battery_holder | BT1 |
| 1 | pickit 1 | 80mill_sqr_test_point | TP1 |
| 1 | pickit 2 | 80mill_test_point | TP2 |
| 1 | pickit 3 | 80mill_test_point | TP3 |
| 1 | pickit 4 | 80mill_test_point | TP4 |
| 1 | pickit 5 | 80mill_test_point | TP5 |
| 1 | Edge | mr-stash_cuts | icon1 |
| 1 | Fsilk | mr-stash_silk | icon2 |
| 1 | Fmask | mr-stash_fmask | icon3 |
| 1 | User | mr-stash_user | icon4 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Metroid | metroid | icon5 |
| 1 | IR OP181 | OP181_TT_electronics_IR | D1 |
| 2 | LS4148 L1G | SOD-80V-LS34 | D2, D3 |
| 4 | XZMDKCBDDG45S-9 | XZMDKCBDDG45S-9-3mm-hole | D4, D5, D6, D7 |
| 2 | 0.1uF | C_0805 | C1, C2 |
| 5 | 22uF | C_0805 | C3, C4, C5, C6, C7 |
| 11 | 10.2k | R_0603 | R1, R2, R3, R4, R6, R7, R20, R21 +3 |
| 1 | 20 | R_1206 | R5 |
| 4 | 200 | R_0603 | R8, R11, R14, R17 |
| 8 | 100 | R_0603 | R9, R10, R12, R13, R15, R16, R18, R19 |
Mr Stash design files
The KiCad project lives in the Wireb/Mr_Stash repository on GitHub; these links point at the commit this page was built from.
- LayoutKiCad/Mr_Stash.kicad_pcb
Mr Stash: common questions
What microcontroller does the Mr Stash use?
The Mr Stash is built around the PIC16F15355-SSOP, from the PIC family.
How big is the Mr Stash PCB?
The Mr Stash measures 101.3 × 63.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Mr Stash?
62 components, from 30 distinct parts. The full bill of materials is listed on this page.
Where can I download the Mr Stash design files?
From the Wireb/Mr_Stash repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Mr Stash design in my own project?
Yes, under the terms of its MIT license, which Wireb chose for the repository.
Can I test firmware for the Mr Stash without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
Similar boards
PIC
Pslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7kPIC
Lens
ervanalb
80 × 80 mm53 parts4LNo license515PIC
Micro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414PIC
GB-CART256K-A
Gekkio
51.4 × 61 mm17 parts2LCC-BY-4.0379PIC
GB-CARTPP-DIY
Gekkio
100 × 100 mm22 parts2LCC-BY-4.0379PIC
GB-LIVE32
Gekkio
51.4 × 61 mm46 parts4LCC-BY-4.0379