30 open source boards using the TSSP58038
Real designs built with the TSSP58038, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Ir smart led controller
dotcypress
11 × 22.1 mm7 parts2LApache-2.010AVR/Arduino
Mainboard
MUNAKATA-EPC
120 × 120 mm151 parts2LNo license2PIC
Mr Stash
Wireb
101.3 × 63.1 mm62 parts2LMIT1NXP
IR PCB
Kushal-Sachdeva78
121.8 × 121.8 mm54 parts2LMIT1STM32
Curio
dotcypress
76.2 × 25.4 mm29 parts4LNo license1STM32
Lap Timer: Timer Board
Dominik-Workshop
50 × 40 mm47 parts2LGPL-3.00STM32
STM32
ravilpatel
41 × 28.8 mm28 parts2LNo license0AVR/Arduino
Automatic door
jessysiman
60.3 × 54.9 mm17 parts2LNo license0ESP32
Electabuzz Unplugged
MayankBagad
167.1 × 181.2 mm11 parts2LNo license0- schematic only · 20 partsESP32
Watt the hack
pandaiscodingcpu
20 partsNo license0 AVR/Arduino
Main board Teensy
MUNAKATA-EPC
120 × 120 mm110 parts2LNo license2STM32
IR
Tomoshibi-technology
96 × 138 mm190 parts2LMIT1Romi unified board-2layer
WPIRoboticsEngineering
125.1 × 125.7 mm71 parts4LNo license1MotionDetector 555Timer
ravilpatel
66 × 33.4 mm19 parts2LNo license0PIC
Main board
MUNAKATA-EPC
109.9 × 109.9 mm75 parts2LNo license2Romi unified board
WPIRoboticsEngineering
125.1 × 125.7 mm68 parts4LNo license1IR board syuuseibann
MUNAKATA-EPC
110 × 110 mm64 parts2LNo license1SensorBoard
MUNAKATA-EPC
100 × 100 mm91 parts2LNo license0Ball
Thrcot
60 × 60 mm49 parts2LNo license0Lap Timer: Receiver Board
Dominik-Workshop
16.5 × 19.7 mm3 parts2LGPL-3.00Romi unified board-2layer-PRE
WPIRoboticsEngineering
125.1 × 125.7 mm68 parts4LNo license1ESP32
IR Japan prot2
Tellurnoid
100 × 100 mm66 parts2LNo license1Jig
WPIRoboticsEngineering
139.5 × 136.2 mm18 parts4LNo license1Sensor
MUNAKATA-EPC
100 × 100 mm59 parts2LNo license0ESP32
IR Japan prot1
Tellurnoid
100 × 100 mm65 parts2LNo license1ESP32
IR Japan prot3
Tellurnoid
100 × 100 mm65 parts2LNo license1ESP32
メインの穴付き
Tellurnoid
100 × 100 mm59 parts2LNo license1AVR/Arduino
IR board
kapibaratomo
99.9 × 99.9 mm18 parts2LNo license0NXP
Main board
MUNAKATA-EPC
120 × 120 mm48 parts2LNo license0Sensors board
MUNAKATA-EPC
119.9 × 122.9 mm34 parts2LNo license0
How designs wire the TSSP58038
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the TSSP58038 connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin has a series resistor on 7 of 16 designs, most often 22 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTpin 1 | Connected to: The microcontroller 28% |
|
| GNDpin 2 | Connected to: GND 81% | — |
| VSpin 3 | Connected to: 3.3V 79% · a signal 21% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ir smart led controller by dotcypress, Main board by MUNAKATA-EPC, Curio by dotcypress and IR PCB by Kushal-Sachdeva78.
The TSSP58038 in open source designs
The gallery holds 30 open source boards using the TSSP58038 from 17 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 57 components.
83% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is Ir smart led controller by dotcypress.
Parts used alongside the TSSP58038
Microcontrollers on boards using the TSSP58038
What boards using the TSSP58038 are built for
TSSP58038: common questions
Where can I find a TSSP58038 reference design?
Each of the 30 boards on this page is a real design using the TSSP58038. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TSSP58038 OUT pin?
The OUT pin has a series resistor on 7 of 16 designs, most often 22 kΩ (then 100 kΩ). Counted from the KiCad layouts of 16 open source designs using the TSSP58038.
What parts are used alongside the TSSP58038?
The CD74HC4067SM, NEO-6M-GPS, open_mv, Seeeduino_Xiao and SeeeduinoXIAO appear in the most repositories here.
Which microcontrollers do boards using the TSSP58038 use?
Most are built on ESP32 (6), STM32 (5), AVR/Arduino (4) and NXP (2).
How big is a typical board using the TSSP58038?
The median is 100 × 100 mm, and 83% are two-layer designs.
What is the most popular open source board using the TSSP58038?
By GitHub stars, Ir smart led controller by dotcypress, with 10 stars.
Can I simulate one of these boards using the TSSP58038 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.