Smart flexispot
wtb04·smart-flexispot·pcb/tab5-desk-ctrl.kicad_pcb
About the Smart flexispot PCB
Smart flexispot is an open source ESP32 PCB design by wtb04, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 80 × 35.2 mm, with 15 components from 11 distinct parts.
Its main chip is the 1x15 female header 2.54mm, from the ESP32 family. By type, the board carries 6 resistors, 3 capacitors, 2 ICs, 2 diodes and 1 fuse.
It belongs with the iot & wireless designs in this gallery.
From the project
Firmware for an M5Stack Tab5 that drives a Flexispot desk and runs the room around it: Home Assistant, Jellyfin, a radar of the planes overhead, the day's timetable and a focus timer. With a simulator and a Bluetooth companion board.
A carrier for an ESP32 DevKit V1 (30-pin) that plugs into a LoctekMotion / Flexispot control box over RJ45. It runs off the desk's 5 V, shifts the box's 5 V signal down for the ESP32, and uses the jack's two LEDs for Bluetooth (BT) and the desk link (LINK). What they show is in getting started. The firmware is in ../proxy.
Rev2, 80 × 35.2 mm, two layers, 4 × M3. The schematic is also a PDF.

Main components on the Smart flexispot
Smart flexispot bill of materials (BOM)
15 components, 11 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 1x15 female header 2.54mm Socket 1x15 2.54mm | PinSocket_1x15_P2.54mm_Vertical | U1A, U1B |
| 1 | SMD1206P050TF/15 PTC 500mA | R_1206_3216Metric | F1 |
| 1 | R-RJ45R08P-C000 RJ45 8P8C 2xLED | RJ45_Connfly_DS1128-09-S8xx-S_Horizontal | RJ45_1 |
| 1 | SS14-E3/61T SS14 | D_SMA | D1 |
| 1 | BAT54S,215 BAT54S | SOT-23 | D2 |
| 1 | 22uF 25V | C_1206_3216Metric | C1 |
| 1 | 100nF 50V | C_0805_2012Metric | C2 |
| 1 | EEU-FR1A471 470uF 10V | CP_Radial_D8.0mm_P3.50mm | C3 |
| 1 | 10K 10k | R_0805_2012Metric | R1 |
| 1 | 15K 15k | R_0805_2012Metric | R2 |
| 4 | 220R | R_0805_2012Metric | R3, R4, R5, R6 |
Smart flexispot design files
The KiCad project lives in the wtb04/smart-flexispot repository on GitHub; these links point at the commit this page was built from.
Smart flexispot: common questions
What microcontroller does the Smart flexispot use?
The Smart flexispot is built around the 1x15 female header 2.54mm, from the ESP32 family.
How big is the Smart flexispot PCB?
The Smart flexispot measures 80 × 35.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Smart flexispot?
15 components, from 11 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Smart flexispot design files?
From the wtb04/smart-flexispot repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Smart flexispot design in my own project?
Yes, under the terms of its Apache-2.0 license, which wtb04 chose for the repository.
Can I test firmware for the Smart flexispot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k