Trs80-m1-drive monitor

xtracool·trs80-m1-drive-monitor·sa400_led_monitor/kicad/sa400_led_monitor.kicad_pcb

Trs80-m1-drive monitor PCB layout, top view — open source board by xtracool

About the Trs80-m1-drive monitor PCB

Trs80-m1-drive monitor is an open source PCB design by xtracool, published on GitHub under the MIT license. It is a 2-layer board measuring 139.7 × 127 mm, with 43 components from 16 distinct parts.

Other key parts include the 74LS14, 74LS00 and 74LS06. By type, the board carries 20 resistors, 11 diodes, 5 capacitors, 3 ICs, 2 connectors and 1 transistor.

From the project

TRS-80 Model 1 floppy drive monitor.

SA400 form-factor board that plugs onto the Shugart 34-pin floppy bus as a fifth "drive" and shows drive-select (red) and write-gate (green) activity for four drives on eight LEDs. Same card-edge tab and AMP Mate-N-Lok power header as a Shugart SA400, same power usage (+5 V logic, +12 V present); 5.5 × 5.0 in. Protected: PTC fuse, P-MOSFET reverse-polarity switch, 5.6 V rail clamp, 470 Ω series resistors between the bus and the receivers so a board fault cannot damage the host.

Main components on the Trs80-m1-drive monitor

Trs80-m1-drive monitor bill of materials (BOM)

43 components, 16 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
74LS14
U1
1
74LS00
U2
1
74LS06
U3
1
IRF4905PBF
Q1
1
Shugart 34-pin card edge
J1
1
AMP 1-641737-1
J2
1
PTC 0.5A
F1
4
RED
D1, D2, D3, D4
4
GREEN
D5, D6, D7, D8
1
1N5339B
D11
2
YELLOW
D12, D13
4
100NF
100nF
C1, C2, C3, C6
1
10UF/16V
10uF/16V
C4
14
470R
R1, R2, R3, R4, R5, R6, R7, R8 +6
5
10K
10k
R9, R10, R11, R12, R13
1
2K2
2k2
R19

Trs80-m1-drive monitor design files

The KiCad project lives in the xtracool/trs80-m1-drive-monitor repository on GitHub; these links point at the commit this page was built from.

Trs80-m1-drive monitor: common questions

How big is the Trs80-m1-drive monitor PCB?

The Trs80-m1-drive monitor measures 139.7 × 127 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Trs80-m1-drive monitor?

43 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Trs80-m1-drive monitor design files?

From the xtracool/trs80-m1-drive-monitor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Trs80-m1-drive monitor design in my own project?

Yes, under the terms of its MIT license, which xtracool chose for the repository.