63 open source boards using the 74LS14
Real designs built with the 74LS14, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Snark barker
schlae
231.1 × 106.7 mm193 parts2LNo license687PIC
NuXT
monotech
184.9 × 243.8 mm214 parts4LGPL-3.0120RP2040/RP2350
Kerberos
FrankBuss
62.5 × 83.8 mm167 parts4LNo license82Zeta sbc
skiselev
170.2 × 100 mm74 partsGPL-3.051ES688 ISA8
hkzlab
104.1 × 99.1 mm121 parts4LCC-BY-NC-4.046C64-Lumafix
tebl
33.7 × 56.5 mm12 parts2LNo license39St251n 20603
schlae
137.4 × 199.1 mm277 parts4LNo license38Sg1000
barbeque
162.2 × 134.6 mm71 parts2LCC-BY-NC-4.033We816
danwerner21
360.1 × 141.4 mm128 parts2LNo license32AVR/Arduino
Polykit Kosmo Multitool
polykit
60 × 150 mm90 parts2LCC-BY-NC-4.031CompaqportableIII
raymondh2
194 × 170.6 mm123 parts2LNo license17Betadisk clone
alvaroalea
99.7 × 149.9 mm83 parts2LNo license7AVR/Arduino
MZ-1500 SD
yanataka60
114.8 × 104.4 mm33 parts2LMIT6ESP8266
Reflow Oven
La-guajolota
100 × 80 mm38 parts2LMIT5TA8-FDC
felge1966
160 × 100.3 mm60 parts2LGPL-3.03Preperf 10x10 V1
ApophisXIV
100 × 100 mm1359 parts8LNo license26809PC
danwerner21
244 × 244 mm155 parts2LNo license2RP2040/RP2350
Pcb
davidmpye
85 × 90 mm83 parts2LGPL-3.02A123-battery integration
MITEVT
66 × 73.7 mm67 parts4LMIT2- schematic only · 28 partsAVR/Arduino
7Driver
Broosky
28 partsNo license2 6502PC
danwerner21
244 × 244 mm154 parts2LNo license1TicTacToe---Using-Digital-Logic
rougeDAG
156 × 133.5 mm139 parts2LNo license1RP2040/RP2350
We816-mark2
danwerner21
360.1 × 141.4 mm128 parts2LNo license18085-explorer
bazsimarkus
120 × 80 mm55 parts2LNo license1AVR/Arduino
DAC-for minimoog
gkaxowns9
132 × 100 mm49 parts2LNo license1OSI-600D-SuperBoard-II
Bambelweeny57
301.5 × 367.4 mm292 parts2LNo license0Snark barker
Vakon84
231.1 × 106.7 mm193 parts2LNo license0Dino v0 0 2
robertrico
298.9 × 222.8 mm179 parts4LNo license0Snark barker mini
computerguy096
103.7 × 78.5 mm175 parts4LCC-BY-SA-4.00Mm8d hw
pozsarzs
238.5 × 59.7 mm83 parts2LCC-BY-NC-4.00PIOI I/O interface module
pozsarzs
238.5 × 59.7 mm83 parts2LEUPL-1.20Before hole repair
apws
160 × 100 mm62 parts2LNo license0Aniol64
vampirehunt2
160.3 × 74.8 mm54 parts2LNo license0Laser card
owhite
201.2 × 112.7 mm52 parts4LNo license0Hobgoblin
iley
150 × 110 mm52 parts2LNo license0NXP
Fiber controller
owhite
201.2 × 112.7 mm52 parts4LNo license0
How designs wire the 74LS14
Read from the KiCad layouts of 52 open source designs, one per repository: what each pin of the 74LS14 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 10 is left unconnected on 38 of 52 designs (a signal on 14).
- Pin 12 is left unconnected on 34 of 52 designs (a signal on 18).
- The VCC pin has a decoupling capacitor on 22 of 52 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 7 | Connected to: GND 94% | — |
| Pin 10 | Connected to: Not connected 73% · a signal 27% | — |
| Pin 12 | Connected to: Not connected 65% · a signal 35% | — |
| VCCpin 14 | Connected to: 5V 92% |
|
10 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Snark barker by schlae, Zynaptik Circuit by zynthian, NuXT by monotech and Kerberos by FrankBuss.
The 74LS14 in open source designs
The gallery holds 63 open source boards using the 74LS14 from 54 GitHub repositories; a typical one measures about 143.6 × 100 mm and carries around 73 components.
80% are two-layer designs, the rest use four layers or more, and 30% carry an open source license.
The most starred is Snark barker by schlae.
Parts used alongside the 74LS14
Microcontrollers on boards using the 74LS14
What boards using the 74LS14 are built for
74LS14: common questions
Where can I find a 74LS14 reference design?
Each of the 63 boards on this page is a real design using the 74LS14. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the 74LS14 pin 10 connected?
Pin 10 is left unconnected on 38 of 52 designs (a signal on 14). Counted from the KiCad layouts of 52 open source designs using the 74LS14.
How is the 74LS14 pin 12 connected?
Pin 12 is left unconnected on 34 of 52 designs (a signal on 18). Counted from the KiCad layouts of 52 open source designs using the 74LS14.
What decoupling capacitors do designs use on the 74LS14 VCC pin?
The VCC pin has a decoupling capacitor on 22 of 52 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 52 open source designs using the 74LS14.
What parts are used alongside the 74LS14?
The 74LS32, 74LS138, 74LS245, 74LS74 and 74LS08 appear in the most repositories here.
Which microcontrollers do boards using the 74LS14 use?
Most are built on AVR/Arduino (7), RP2040/RP2350 (3), ESP32 (1) and ESP8266 (1).
How big is a typical board using the 74LS14?
The median is 143.6 × 100 mm, and 80% are two-layer designs.
What is the most popular open source board using the 74LS14?
By GitHub stars, Snark barker by schlae, with 687 stars.
Can I simulate one of these boards using the 74LS14 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.