Receiver cart
yinipi·HaptiPointer-Studio·Matériel/carte_receiver/receiver_cart.kicad_pcb
About the Receiver cart PCB
Receiver cart is an open source AVR/Arduino PCB design by yinipi, published on GitHub. It is a 2-layer board measuring 92.7 × 54.8 mm, with 41 components from 32 distinct parts.
Its main chip is the ATMEGA32U4-A, from the AVR/Arduino family. Other key parts include the LM1117DT-3.3. By type, the board carries 17 capacitors, 11 resistors, 3 inductors, 2 ICs, 2 crystals and 2 connectors.
From the project
Dual-board KiCad hardware, ATmega32U4 bare-metal C firmware (USB CDC), and Python GUI to configure presentation timers directly into EEPROM
Main components on the Receiver cart
Receiver cart bill of materials (BOM)
41 components, 32 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATMEGA32U4-A ATmega32U4-A | TQFP-44_10x10mm_P0.8mm | U1 |
| 1 | LM1117DT-3.3 LM1117S-3.3 | SOT-223-3_TabPin2 | U3 |
| 1 | CRYSTAL_GND24 Crystal_GND24 | Crystal_SMD_SeikoEpson_FA238-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | Crystal_GND24 | Crystal_SMD_SeikoEpson_FA238-4Pin_3.2x2.5mm_HandSoldering | Y3 |
| 1 | USB_A | USB_A_Molex_48037-2200_Horizontal | J2 |
| 1 | Conn_01x03_Female | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | Antenna_Shield | Texas_SWRA117D_2.4GHz_Right | AE1 |
| 1 | Conn_02x04_Counter_Clockwise | PinSocket_2x04_P2.54mm_Vertical | nrf24l01 |
| 2 | LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | Alim1, Trans1 |
| 1 | 8.2NH 8.2nH | L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1 |
| 1 | 3.9NH 3.9nH | L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L2 |
| 1 | 2.7NH 2.7nH | L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L3 |
| 2 | 22PF 22pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2 |
| 1 | 1µF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 3 | 100N 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C5, C6 |
| 1 | 100N 1nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7 |
| 1 | 100NF 10nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8 |
| 3 | 22pf | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C10, C11 |
| 1 | 2.2nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12 |
| 1 | 10NF 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13 |
Show 12 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 22PF 4.7pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C14 |
| 1 | 1NF 1.5pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C15 |
| 1 | 22PF 1pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C16 |
| 1 | 22PF 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C17 |
| 2 | 330 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 1 | 330 500 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 2 | 500 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5 |
| 2 | 100K 510 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R7 |
| 1 | 470 22k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8 |
| 1 | 22K 1M | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9 |
| 1 | 22 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 1 | 10K 22 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11 |
Receiver cart design files
The KiCad project lives in the yinipi/HaptiPointer-Studio repository on GitHub; these links point at the commit this page was built from.
Receiver cart: common questions
What microcontroller does the Receiver cart use?
The Receiver cart is built around the ATMEGA32U4-A, from the AVR/Arduino family.
How big is the Receiver cart PCB?
The Receiver cart measures 92.7 × 54.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Receiver cart?
41 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Receiver cart design files?
From the yinipi/HaptiPointer-Studio repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Receiver cart design in my own project?
The repository has no license, so all rights stay with yinipi. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Receiver cart without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in HaptiPointer-Studio
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k