Main cart
yinipi·HaptiPointer-Studio·Matériel/carte_principale/main_cart.kicad_pcb
About the Main cart PCB
Main cart is an open source AVR/Arduino PCB design by yinipi, published on GitHub. It is a 2-layer board measuring 95.1 × 85.4 mm, with 68 components from 46 distinct parts.
Its main chip is the ATMEGA32U4-A, from the AVR/Arduino family. Other key parts include the MAX1811, LM1117DT-3.3 and NRF24L01. By type, the board carries 22 capacitors, 17 resistors, 4 ICs, 3 diodes, 3 inductors and 2 crystals.
From the project
Dual-board KiCad hardware, ATmega32U4 bare-metal C firmware (USB CDC), and Python GUI to configure presentation timers directly into EEPROM
Main components on the Main cart
Main cart bill of materials (BOM)
68 components, 46 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATMEGA32U4-A ATmega32U4-A | TQFP-44_10x10mm_P0.8mm | U1 |
| 1 | MAX1811 | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | LM1117DT-3.3 | SOT-223-3_TabPin2 | U3 |
| 1 | NRF24L01 | QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm | U4 |
| 1 | 2N7002 | SOT-23 | Q1 |
| 1 | CRYSTAL_GND24 Crystal_GND24 | Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | CRYSTAL_GND24 Crystal_GND24 | Crystal_SMD_SeikoEpson_FA238-4Pin_3.2x2.5mm_HandSoldering | Y2 |
| 1 | USB_A | USB_A_Molex_48037-2200_Horizontal | J1 |
| 1 | CONN_01X04 Conn_01x04 | PinSocket_1x04_P2.54mm_Vertical | J6 |
| 1 | Antenna_Shield | Texas_SWRA117D_2.4GHz_Right | AE1 |
| 1 | AVR-ISP-6 | PinSocket_2x03_P2.54mm_Vertical | AVR1 |
| 2 | SW_Push | SW_Push_1P1T_NO_CK_KSC7xxJ | SWHwb1, reset1 |
| 4 | SW_Push | SW_PUSH_6mm_H4.3mm | Slaser1, next1, prev1, start1 |
| 1 | SW_SPDT_312 | PinHeader_1x03_P2.54mm_Vertical | commut1 |
| 2 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | laser1, motor1 |
| 1 | Conn_02x04_Counter_Clockwise | PinSocket_2x04_P2.54mm_Vertical | nrf24l01 |
| 1 | Conn_01x03_Pin | JST_EH_S3B-EH_1x03_P2.50mm_Horizontal | pile1 |
| 1 | LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | led_usb1 |
| 1 | led_charge | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | D_Schottky | D_SOD-123 | D2 |
Show 26 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LED | LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3 |
| 1 | 8.2NH 8.2nH | L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1 |
| 1 | 3.9NH 3.9nH | L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L2 |
| 1 | 2.7NH 2.7nH | L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L3 |
| 5 | 22PF 22pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C14, C16, C17 |
| 1 | 1µ | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 4 | 100N 100n | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C5, C6, C7 |
| 1 | 100NF 100nf | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8 |
| 2 | 4.7µF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C12 |
| 2 | 1µF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10, C11 |
| 1 | 10NF 10nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13 |
| 1 | 1NF 1nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C15 |
| 1 | 2.2NF 2.2nF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C18 |
| 1 | 4.7PF 4.7pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C19 |
| 1 | 1.5PF 1.5pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C20 |
| 1 | 1PF 1pF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C21 |
| 1 | 0.1µF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C22 |
| 3 | 330 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3 |
| 2 | 22 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R5 |
| 2 | 100K 100k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R7 |
| 1 | 470 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8 |
| 1 | 22K 22k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9 |
| 1 | 1M | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 3 | 10K 10k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11, R13, R14 |
| 2 | 510 | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R12, R17 |
| 2 | 4.7K 4.7k | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R15, R16 |
Main cart design files
The KiCad project lives in the yinipi/HaptiPointer-Studio repository on GitHub; these links point at the commit this page was built from.
Main cart: common questions
What microcontroller does the Main cart use?
The Main cart is built around the ATMEGA32U4-A, from the AVR/Arduino family.
How big is the Main cart PCB?
The Main cart measures 95.1 × 85.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Main cart?
68 components, from 46 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Main cart design files?
From the yinipi/HaptiPointer-Studio repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Main cart design in my own project?
The repository has no license, so all rights stay with yinipi. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Main cart without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in HaptiPointer-Studio
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k