Zaid fly swarm

zaljerme·zaid-fly-swarm·hardware/kicad/zaid-fly.kicad_pcb

Zaid fly swarm PCB layout, top view — open source ESP32 board by zaljerme

About the Zaid fly swarm PCB

Zaid fly swarm is an open source ESP32 PCB design by zaljerme, published on GitHub under the MIT license. It is a 2-layer board measuring 28 × 38 mm, with 45 components from 17 distinct parts.

Its main chip is the Seeed 113991114, from the ESP32 family. Other key parts include the TDK InvenSense MPU-6050 (LCSC C24112). By type, the board carries 15 resistors, 10 diodes, 8 capacitors, 4 modules, 4 transistors and 2 ICs.

It belongs with the robotics & motion and power & battery designs in this gallery.

From the project

28 × 38 mm, 2-layer, 1.0 mm FR-4. The XIAO ESP32-S3 sits on low-profile headers above the SMD parts, so the whole flight controller fits on a footprint not much bigger than the XIAO.

28 × 38 mm, 2-layer, 1.0 mm FR-4. The XIAO ESP32-S3 sits on low-profile headers above the SMD parts, so the whole flight controller fits on a footprint not much bigger than the XIAO.

To change a part value, net or position, edit generatekicad.py` and run:

It also runs a courtyard-overlap and board-edge check before writing anything.

The board ships placed with nets assigned. Route it in KiCad, or run Freerouting through the KiCad plugin and then tidy up by hand:

Zaid fly swarm, from the project README
From the project README

Main components on the Zaid fly swarm

TDK InvenSense MPU-6050 (LCSC C24112)Seeed 113991114

Zaid fly swarm bill of materials (BOM)

45 components, 17 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TDK InvenSense MPU-6050 (LCSC C24112)
MPU-6050
U1
1
Seeed 113991114
Seeed XIAO ESP32-S3
U2
4
720 coreless brushed motor (7x20 mm)
Motor
M1, M2, M3, M4
4
SI2300 N-MOSFET (C10487)
SI2300
Q1, Q2, Q3, Q4
1
JST-PH 2.0 pigtail, 1S 3.7V
1S LiPo
J1
1
wire link to XIAO BAT+/BAT- pads
XIAO BAT
J2
4
1N4148WS flyback (C2128)
1N4148WS
D1, D2, D3, D4
3
0603 red LED (C2286)
Red
D5, D9, D10
1
0603 green LED (C72043)
Green
D6
2
0603 white LED (C2290)
White
D7, D8
6
0603 X7R 16V (C14663)
0.1uF
C1, C2, C3, C4, C5, C6
2
0603 X7R 50V (C57112)
0.01uF
C7, C8
4
0603 1% gate pull-down (C25804)
10k
R1, R2, R3, R4
5
0603 1% (C25804)
10k
R5, R6, R7, R8, R9
2
0603 1%
200
R10, R11
2
0603 1%
100
R12, R13
2
0603 1%
150
R14, R15

Zaid fly swarm design files

The KiCad project lives in the zaljerme/zaid-fly-swarm repository on GitHub; these links point at the commit this page was built from.

Zaid fly swarm: common questions

What microcontroller does the Zaid fly swarm use?

The Zaid fly swarm is built around the Seeed 113991114, from the ESP32 family.

How big is the Zaid fly swarm PCB?

The Zaid fly swarm measures 28 × 38 mm, has 2 copper layers and is 1 mm thick.

How many components are on the Zaid fly swarm?

45 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Zaid fly swarm design files?

From the zaljerme/zaid-fly-swarm repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Zaid fly swarm design in my own project?

Yes, under the terms of its MIT license, which zaljerme chose for the repository.

Can I test firmware for the Zaid fly swarm without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards