2ESP Breakout
About the 2ESP Breakout
2ESP Breakout is an open source ESP32 PCB design by 617quan, published on GitHub. It is a 2-layer board measuring 134.6 × 124.5 mm, with 39 components from 4 distinct parts.
Its main chip is the PinSocket_1x15_P2.54mm_Vertical, from the ESP32 family.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Senior Design Project
2ESP Breakout bill of materials (BOM)
39 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 14 | Conn_01x02_Socket | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J2, J3, J4, J5, J6, J7, J9, J10 +6 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | Buck_Header1 |
| 12 | Conn_01x06_Socket | JST_PH_B6B-PH-K_1x06_P2.00mm_Vertical | DRIVE1, DRIVE2, DRIVE3, DRIVE4, LIFT1, LIFT2, LIFT3, LIFT4 +4 |
| 12 | Conn_01x15_Socket | PinSocket_1x15_P2.54mm_Vertical | ESP1L_1, ESP1L_2, ESP1R_1, ESP1R_2, ESP2L_1, ESP2L_2, ESP2R_1, ESP2R_2 +4 |
2ESP Breakout design files
The KiCad project lives in the 617quan/NeonCarrot repository on GitHub; these links point at the commit this page was built from.
2ESP Breakout: common questions
What microcontroller does the 2ESP Breakout use?
The 2ESP Breakout is built around the PinSocket_1x15_P2.54mm_Vertical, from the ESP32 family.
How big is the 2ESP Breakout?
The 2ESP Breakout measures 134.6 × 124.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the 2ESP Breakout?
39 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the 2ESP Breakout design files?
From the 617quan/NeonCarrot repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the 2ESP Breakout design in my own project?
The repository has no license, so all rights stay with 617quan. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the 2ESP Breakout without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in NeonCarrot
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k