AVA-Robot-
AalindOg·AVA-Robot-·hardware/ava-carrier.kicad_pcb
About the AVA-Robot- PCB
AVA-Robot- is an open source ESP32 PCB design by AalindOg, published on GitHub. It is a 2-layer board measuring 60 × 40 mm, with 14 components from 14 distinct parts.
Its main chip is the XIAO ESP32-S3 Sense, from the ESP32 family. Other key parts include the Buck 5V/5A Module and TB6612FNG Motor Driver. By type, the board carries 5 connectors, 3 ICs, 2 diodes, 2 resistors, 1 fuse and 1 switch.
It belongs with the robotics & motion, power & battery and audio designs in this gallery.
From the project
A mobile AI companion robot powered by Hermes Agent. Built by Aalind Tiwari.
A mobile AI companion robot powered by Hermes Agent. Built by Aalind Tiwari.
AVA is a wheeled AI companion with a touchscreen, camera, speaker, sensors and motors, all packed into a 3D-printed enclosure. A single-board computer runs the high-level AI, a XIAO ESP32-S3 Sense handles audio/IMU sensing and motor control, and a custom carrier board ties the power and drive system together.

Main components on the AVA-Robot-
AVA-Robot- bill of materials (BOM)
14 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Buck 5V/5A Module | U1_SOCKET | U1 |
| 1 | TB6612FNG Motor Driver | U2_SOCKET | U2 |
| 1 | XIAO ESP32-S3 Sense | U3_SOCKET | U3 |
| 1 | LiPo 2S In (JST-PH) | J1_SOCKET | J1 |
| 1 | Motor A (JST-PH) | J2_SOCKET | J2 |
| 1 | Motor B (JST-PH) | J3_SOCKET | J3 |
| 1 | I2C Expansion | J4_SOCKET | J4 |
| 1 | SBC 5V Feed (JST-VH) | J5_SOCKET | J5 |
| 1 | Polyfuse 5A | F1_SOCKET | F1 |
| 1 | Power Switch | SW1_SOCKET | SW1 |
| 1 | LED +5V | D1_SOCKET | D1 |
| 1 | LED VBAT | D2_SOCKET | D2 |
| 1 | 1k | R1_SOCKET | R1 |
| 1 | 1k | R2_SOCKET | R2 |
AVA-Robot- design files
The KiCad project lives in the AalindOg/AVA-Robot- repository on GitHub; these links point at the commit this page was built from.
- Layouthardware/ava-carrier.kicad_pcb
- Schematichardware/ava-carrier.kicad_sch
- BOMbom.csv
AVA-Robot-: common questions
What microcontroller does the AVA-Robot- use?
The AVA-Robot- is built around the XIAO ESP32-S3 Sense, from the ESP32 family.
How big is the AVA-Robot- PCB?
The AVA-Robot- measures 60 × 40 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the AVA-Robot-?
14 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the AVA-Robot- design files?
From the AalindOg/AVA-Robot- repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the AVA-Robot- design in my own project?
The repository has no license, so all rights stay with AalindOg. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the AVA-Robot- without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k