Controller-Drone-

adirock09·Controller-Drone-·PCB/DroneController.kicad_pcb

Controller-Drone- PCB layout, top view — open source STM32 board by adirock09

About the Controller-Drone- PCB

Controller-Drone- is an open source STM32 PCB design by adirock09, published on GitHub. It is a 2-layer board measuring 59.8 × 39.6 mm, with 43 components from 25 distinct parts.

Its main chip is the STM32F401CBUx, from the STM32 family. Other key parts include the AMS1117-3.3, MPU-6050, BMP280 and L7805. By type, the board carries 18 capacitors, 10 connectors, 5 ICs, 4 resistors, 3 diodes and 2 switches.

It belongs with the robotics & motion and sensors designs in this gallery.

From the project

- STM32f4 cortex M4 based on board microcontroller for precision and fligt data simulation - MPU9250.(IMU) for statbility and orientation of board/vehicle. - BMP280 .(Barometer) barometer for altitude calculations . helps to hover the flight.

- STM32f4 cortex M4 based on board microcontroller for precision and fligt data simulation - MPU9250.(IMU) for statbility and orientation of board/vehicle. - BMP280 .(Barometer) barometer for altitude calculations . helps to hover the flight.

- ## Bill of Materials (BOM) | Serial Num | Description | Total (USD) | |----:|--------------------------|-------------| | 1 | PCB and Assembly |127.46 | | 2 | Shipping JLCPCB |14.35 |

Controller-Drone-, from the project README
From the project README

Main components on the Controller-Drone-

Controller-Drone- bill of materials (BOM)

43 components, 25 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AMS1117-3.3
U1
1
MPU-6050
U2
1
BMP280
U3
1
STM32F401CBUx
U4
1
L7805
U5
1
Crystal_GND23_Small
Y1
1
USB_B_Mini
J1
5
Conn_01x03_Male
J2, J3, J4, J5, J8
1
Conn_01x04_Pin
J6
1
Conn_01x02_Male
J7
1
Conn_01x03_Male
J9
1
Conn_01x04_Pin
J10
1
SW_Push
SW1
1
SW_SPDT
SW3
1
GREEN
D1
1
blue
D2
1
RED
D3
2
10uf
C1, C15
4
0.1uf
C2, C4, C5, C16
1
10nf
C3
Show 5 more
QtyPartRefs
2
100nf
C6, C8
1
2.2nf
C7
2
12pf
C9, C10
6
100pf
C11, C12, C13, C14, C17, C18
4
1k
R1, R2, R3, R5

Controller-Drone- design files

The KiCad project lives in the adirock09/Controller-Drone- repository on GitHub; these links point at the commit this page was built from.

Controller-Drone-: common questions

What microcontroller does the Controller-Drone- use?

The Controller-Drone- is built around the STM32F401CBUx, from the STM32 family.

How big is the Controller-Drone- PCB?

The Controller-Drone- measures 59.8 × 39.6 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Controller-Drone-?

43 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Controller-Drone- design files?

From the adirock09/Controller-Drone- repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Controller-Drone- design in my own project?

The repository has no license, so all rights stay with adirock09. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Controller-Drone- without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

Similar boards