ShakeMe
ahmadjamal789·ShakeMe·PCB Design/shakeMe.kicad_pcb
About the ShakeMe PCB
ShakeMe is an open source RP2040/RP2350 PCB design by ahmadjamal789, published on GitHub. It is a 2-layer board measuring 53.1 × 29.5 mm, with 9 components from 9 distinct parts.
Its main chip is the SC0917, from the RP2040/RP2350 family. Other key parts include the TP4056_TYPEC, ST7789_2.0_TFT and MPU6050. By type, the board carries 4 ICs, 2 switches, 2 capacitors and 1 diode.
It belongs with the displays & leds, sensors and power & battery designs in this gallery.
From the project
A handheld motion-reactive display where particles in a virtual solvent settle at rest and disperse when shaken, driven by an IMU and rendered on a color TFT.
A handheld, battery-powered display that behaves like a solute in a solvent. Left at rest, the particles on screen settle to the bottom. Shake or move it, and they are kicked up and spread through the whole volume. When the motion stops, they slowly resettle.
Built for Hack Club, Week 4: Displays Week ("Design with Displays").
A motion sensor measures how hard the device is being disturbed, and that measurement drives a particle simulation drawn on a color TFT.
Main components on the ShakeMe
ShakeMe bill of materials (BOM)
9 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TP4056_TYPEC TP4056_TypeC | Charger_TP4056_TypeC_Protected | U1 |
| 1 | ST7789_2.0_TFT | Display_ST7789_2in_8pin | U2 |
| 1 | SC0917 | MODULE_SC0917 | U4 |
| 1 | MPU6050 | PinHeader_1x08_P2.54mm_Vertical | U5 |
| 1 | SW_Push | SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW1 |
| 1 | Power_sw | SW_DIP_SPSTx01_Slide_6.7x4.1mm_W7.62mm_P2.54mm_LowProfile | SW3 |
| 1 | BAT42W-V | D_SOD-123 | D2 |
| 1 | 10uF, 10V | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 1 | 100NF 100nF | C_1808_4520Metric_Pad1.72x2.30mm_HandSolder | C3 |
ShakeMe design files
The KiCad project lives in the ahmadjamal789/ShakeMe repository on GitHub; these links point at the commit this page was built from.
ShakeMe: common questions
What microcontroller does the ShakeMe use?
The ShakeMe is built around the SC0917, from the RP2040/RP2350 family.
How big is the ShakeMe PCB?
The ShakeMe measures 53.1 × 29.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ShakeMe?
9 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the ShakeMe design files?
From the ahmadjamal789/ShakeMe repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the ShakeMe design in my own project?
The repository has no license, so all rights stay with ahmadjamal789. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the ShakeMe without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
Similar boards
RP2040/RP2350
OSO-BOOK-C1
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1kRP2040/RP2350
Corne chocolate
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
Corne cherry
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7kRP2040/RP2350
LogicAnalyzer
gusmanb
57 × 55.2 mm6 parts2LGPL-3.05.0kRP2040/RP2350
Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0kRP2040/RP2350
Main
google
98 × 71 mm102 parts2LApache-2.02.9k