Inverter
alheir·EPOT-G3-Q12025·tps/tp3/pcb/kicad/inverter.kicad_pcb
About the Inverter PCB
Inverter is an open source ESP32 PCB design by alheir, published on GitHub under the MIT license. It is a 2-layer board measuring 100 × 121 mm, with 94 components from 28 distinct parts.
Its main chip is the ESP32-DEVKIT-V1, from the ESP32 family. Other key parts include the IR2110-A, IR2110-B and IR2110-C. By type, the board carries 25 capacitors, 24 test points, 18 resistors, 8 connectors, 8 diodes and 6 transistors.

Main components on the Inverter
Inverter bill of materials (BOM)
94 components, 28 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | IR2110-A | DIP-14_W7.62mm_Socket_LongPads | U1 |
| 1 | IR2110-B | DIP-14_W7.62mm_Socket_LongPads | U2 |
| 1 | IR2110-C | DIP-14_W7.62mm_Socket_LongPads | U3 |
| 1 | ESP32-DEVKIT-V1 | MODULE_ESP32_DEVKIT_V1 | U4 |
| 6 | IRF820 | TO-220-3_Vertical | Q1, Q2, Q3, Q4, Q5, Q6 |
| 1 | 220Vac In | TerminalBlock_bornier-2_P5.08mm | J1 |
| 1 | Motor | TerminalBlock_bornier-3_P5.08mm | J2 |
| 1 | 5Vext In | Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J3 |
| 3 | Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Vertical | J4, J5, J8 |
| 1 | 15Vext In | Molex_KK-254_AE-6410-02A_1x02_P2.54mm_Vertical | J6 |
| 1 | Vd out | TerminalBlock_bornier-2_P5.08mm | J7 |
| 1 | 10k | Potentiometer_Alps_RK163_Single_Horizontal | RV1 |
| 24 | TestPoint | PinHeader_1x01_P2.54mm_Vertical | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 +16 |
| 3 | FR104 | D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2, D3 |
| 1 | W10M | Diode_Bridge_Round_D9.0mm | D4 |
| 4 | Red | LED_D3.0mm | D5, D6, D7, D8 |
| 8 | 10u-25V | CP_Radial_D4.0mm_P1.50mm | C1, C2, C3, C17, C23, C25, C26, C27 |
| 11 | 1u-50V | C_Disc_D4.7mm_W2.5mm_P5.00mm | C4, C5, C6, C7, C8, C9, C10, C11 +3 |
| 3 | 22n-400V | C_Rect_L11.5mm_W4.0mm_P10.00mm_MKT | C13, C14, C15 |
| 1 | 100u-450V | CP_Radial_D17.0mm_P7.50mm | C16 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10n-400V | C_Rect_L11.5mm_W4.5mm_P10.00mm_MKT | C18 |
| 1 | 47u-450V | CP_Radial_D16.0mm_P7.50mm | C21 |
| 6 | 18 | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6 |
| 1 | 560 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 1 | 220 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
| 6 | 10 | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R9, R10, R11, R12, R13, R14 |
| 1 | 2.7k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
| 3 | 150k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R16, R17, R18 |
Inverter design files
The KiCad project lives in the alheir/EPOT-G3-Q12025 repository on GitHub; these links point at the commit this page was built from.
Inverter: common questions
What microcontroller does the Inverter use?
The Inverter is built around the ESP32-DEVKIT-V1, from the ESP32 family.
How big is the Inverter PCB?
The Inverter measures 100 × 121 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Inverter?
94 components, from 28 distinct parts. The full bill of materials is listed on this page.
Where can I download the Inverter design files?
From the alheir/EPOT-G3-Q12025 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Inverter design in my own project?
Yes, under the terms of its MIT license, which alheir chose for the repository.
Can I test firmware for the Inverter without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in EPOT-G3-Q12025
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k