Custom-Audio-Player
anshvirmani31-bit·Custom-Audio-Player
About the Custom-Audio-Player PCB
Custom-Audio-Player is an open source ESP32 PCB design by anshvirmani31-bit, published on GitHub. It is a 2-layer board measuring 69.7 × 69 mm, with 29 components from 16 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AP2112K-3.3 and MAX98357A. By type, the board carries 8 capacitors, 8 resistors, 7 switches, 3 ICs and 3 connectors.
It belongs with the audio designs in this gallery.
From the project
Plays custom audio when you touch/click certain parts and things. The auido files it plays must be compressed as there is no external sd card slot, it is based of an esp32
This is a small audio file player with it's own standalone speaker based of an ESP-32-S3-WROOM-1. You can insert your own audio files however it has no external SD card slot meaning you only get the amount of local storage available on the ESP-32. This could be a potential downside because your file(s) will have to be heavily compressed. The reason I chose to design it like this is to keep the cost down and simpler to design.
Main components on the Custom-Audio-Player
Custom-Audio-Player bill of materials (BOM)
29 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | MAX98357A | TQFN-16-1EP_3x3mm_P0.5mm_EP1.23x1.23mm | U3 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | Conn_01x02_Pin | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Conn_01x04_Pin | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | RotaryEncoder_Switch | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW1 |
| 1 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW2 |
| 5 | SW_Push | Single Touchpad | SW3, SW4, SW5, SW6, SW7 |
| 4 | 10uF | C_0805_2012Metric | C1, C2, C4, C7 |
| 2 | 1uF | C_0805_2012Metric | C3, C6 |
| 2 | 100nF | C_0805_2012Metric | C5, C8 |
| 2 | 5.1k | R_0805_2012Metric | R1, R11 |
| 3 | 10k | R_0805_2012Metric | R2, R6, R7 |
| 1 | 100k | R_0805_2012Metric | R3 |
| 2 | 4.7k | R_0805_2012Metric | R4, R5 |
Custom-Audio-Player design files
The KiCad project lives in the anshvirmani31-bit/Custom-Audio-Player repository on GitHub; these links point at the commit this page was built from.
- LayoutWeek 5 PCB.kicad_pcb
- SchematicWeek 5 PCB.kicad_sch
- BOMBOM.csv
Custom-Audio-Player: common questions
What microcontroller does the Custom-Audio-Player use?
The Custom-Audio-Player is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Custom-Audio-Player PCB?
The Custom-Audio-Player measures 69.7 × 69 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Custom-Audio-Player?
29 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Custom-Audio-Player design files?
From the anshvirmani31-bit/Custom-Audio-Player repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Custom-Audio-Player design in my own project?
The repository has no license, so all rights stay with anshvirmani31-bit. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Custom-Audio-Player without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k