Test reusable workflow
AntarktisZ11·test_reusable_workflow·pcb/ESP32-CAM-WebServer-Circuit.kicad_pcb
About the Test reusable workflow PCB
Test reusable workflow is an open source ESP32 PCB design by AntarktisZ11, published on GitHub. It is a 2-layer board measuring 30.5 × 48.3 mm, with 12 components from 10 distinct parts.
Its main chip is the ESP32-CAM, from the ESP32 family. Other key parts include the TP4056-MODULE and XC6503D331MR-G. By type, the board carries 3 ICs, 3 capacitors, 2 transistors, 2 resistors, 1 connector and 1 switch.
Main components on the Test reusable workflow
Test reusable workflow bill of materials (BOM)
12 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-CAM | ESP32CAM | IC1 |
| 1 | TP4056-MODULE TP4056-Module | TP4056-Module | U1 |
| 1 | XC6503D331MR-G | SOT-23-5 | U2 |
| 1 | 2N7002 | SOT-23 | Q1 |
| 1 | IRLML0030 | SOT-23 | Q2 |
| 1 | CONN_01X02 Conn_01x02 | PinHeader_1x02_P2.00mm_Vertical | J1 |
| 1 | EG1270 | EG1270 | SW1 |
| 2 | 100N 100n | C_0603_1608Metric | C1, C2 |
| 1 | 1u | C_0603_1608Metric | C3 |
| 2 | 10K 10k | R_0603_1608Metric | R1, R2 |
Test reusable workflow design files
The KiCad project lives in the AntarktisZ11/test_reusable_workflow repository on GitHub; these links point at the commit this page was built from.
Test reusable workflow: common questions
What microcontroller does the Test reusable workflow use?
The Test reusable workflow is built around the ESP32-CAM, from the ESP32 family.
How big is the Test reusable workflow PCB?
The Test reusable workflow measures 30.5 × 48.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Test reusable workflow?
12 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Test reusable workflow design files?
From the AntarktisZ11/test_reusable_workflow repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Test reusable workflow design in my own project?
The repository has no license, so all rights stay with AntarktisZ11. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Test reusable workflow without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k