Expansion
anton-vinogradov·esp32-leshy2·drafts/legacy-2026-08-22/tscircuit-pre-g2f3i/expansion.kicad_pcb
About the Expansion PCB
Expansion is an open source PCB design by anton-vinogradov, published on GitHub under the MIT license. It is a 2-layer board measuring 80 × 60 mm, with 13 components from 8 distinct parts.
By type, the board carries 3 diodes, 3 capacitors, 2 ICs, 2 connectors, 2 resistors and 1 battery holder.
It belongs with the rf & radio designs in this gallery.
From the project
Open multiband RF handheld on ESP32-S3 + ESP32-C5 — successor to esp32-leshy / ESP32-DIV
2.4/5-GHz Wi‑Fi · BLE · 802.15.4 · 3× nRF24 · Sub‑GHz · VHF/UHF · FM/AM/SW/LW/Airband · IR · LoRa/CC1101+NFC Cap
Capabilities · Roadmap · Stage reports · Schematics · Firmware · Русский
Leshy2 is intended to be a hobby device combining spectrum observation, communication, diagnostics and safe experimentation without a mandatory laptop. The first order targets one genuinely working prototype: the factory supplies two populated PCBAs and the owner completes a simple, solder-free final assembly.
Expansion bill of materials (BOM)
13 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | — | chip | U40 |
| 1 | — | chip_soic8 | U44 |
| 2 | — | chip | J40, J41 |
| 1 | — | chip | BT40 |
| 3 | — | chip | D40, D41, D42 |
| 1 | 10uF | capacitor_cap0805 | Cbulk40 |
| 2 | 100nF | capacitor_cap0402 | Cio40, Cvcc40 |
| 2 | 4.7kΩ | resistor_res0402 | R40, R41 |
Expansion design files
The KiCad project lives in the anton-vinogradov/esp32-leshy2 repository on GitHub; these links point at the commit this page was built from.
Expansion: common questions
How big is the Expansion PCB?
The Expansion measures 80 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Expansion?
13 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Expansion design files?
From the anton-vinogradov/esp32-leshy2 repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Expansion design in my own project?
Yes, under the terms of its MIT license, which anton-vinogradov chose for the repository.
More boards in esp32-leshy2
Leshy2 LESHY2-RF-R2 R2 exact placement
anton-vinogradov
80 × 150 mm778 parts6LMIT6ESP32
Leshy2 LESHY2-UI-R2 R2 exact placement
anton-vinogradov
80 × 150 mm430 parts6LMIT6Power
anton-vinogradov
90 × 70 mm42 parts2LMIT6Indicators
anton-vinogradov
90 × 70 mm37 parts2LMIT6Audio
anton-vinogradov
80 × 60 mm19 parts2LMIT6
Similar boards
Hat
pa3gsb
65 × 56 mm81 parts2LNo license675Radioberry juice
pa3gsb
65 × 56 mm87 parts2LNo license675Radioberry preamp
pa3gsb
65 × 56 mm137 parts2LNo license675Goodwatch20
travisgoodspeed
25.6 × 27.6 mm20 parts2LNo license568GoodPocketWatch
travisgoodspeed
75.2 × 101.2 mm56 parts2LNo license568Goodwatch31
travisgoodspeed
25.6 × 27.6 mm23 parts2LNo license568