Power
anton-vinogradov·esp32-leshy2·drafts/legacy-2026-08-22/tscircuit-pre-g2f3i/power.kicad_pcb
About the Power PCB
Power is an open source PCB design by anton-vinogradov, published on GitHub under the MIT license. It is a 2-layer board measuring 90 × 70 mm, with 42 components from 23 distinct parts.
By type, the board carries 16 resistors, 10 capacitors, 5 ICs, 3 inductors, 2 transistors and 2 connectors.
It belongs with the rf & radio designs in this gallery.
From the project
Open multiband RF handheld on ESP32-S3 + ESP32-C5 — successor to esp32-leshy / ESP32-DIV
2.4/5-GHz Wi‑Fi · BLE · 802.15.4 · 3× nRF24 · Sub‑GHz · VHF/UHF · FM/AM/SW/LW/Airband · IR · LoRa/CC1101+NFC Cap
Capabilities · Roadmap · Stage reports · Schematics · Firmware · Русский
Leshy2 is intended to be a hobby device combining spectrum observation, communication, diagnostics and safe experimentation without a mandatory laptop. The first order targets one genuinely working prototype: the factory supplies two populated PCBAs and the owner completes a simple, solder-free final assembly.
Power bill of materials (BOM)
42 components, 23 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | — | chip | U2, U3, U4, U5, U6 |
| 2 | — | chip | Q1, Q2 |
| 2 | — | chip | J1, J2 |
| 1 | — | chip_pinrow3 | BT1 |
| 1 | 50mΩ | resistor_res1210 | F1 |
| 1 | 10mΩ | resistor_res1210 | SW1 |
| 1 | 1MΩ | resistor_res0603 | D1 |
| 2 | 2.2µH | inductor_1210 | L1, L3 |
| 1 | 4.7µH | inductor_1210 | L2 |
| 2 | 100nF | capacitor_cap0402 | Cbst4, Cbst5 |
| 4 | 22uF | capacitor_cap0805 | Cin3, Cin5, Cout3, Cout5 |
| 1 | 1uF | capacitor_cap0402 | Cin3a |
| 1 | 2.2uF | capacitor_cap0402 | Cout3a |
| 2 | 0.1uF | capacitor_cap0402 | Cvcc4, Cvcc5 |
| 1 | 52.3kΩ | resistor_res0402 | R1 |
| 2 | 10kΩ | resistor_res0402 | R2, R4 |
| 1 | 31.6kΩ | resistor_res0402 | R3 |
| 1 | 10kΩ | resistor_res0603 | RT1 |
| 1 | 30.1kΩ | resistor_res0402 | RT2 |
| 5 | 100kΩ | resistor_res0402 | R_EN3H, R_RE3A, R_RE5, Raam4, Raam5 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 47kΩ | resistor_res0402 | R_EN3L |
| 2 | 20Ω | resistor_res0402 | Rbst4, Rbst5 |
| 2 | 5.1kΩ | resistor_res0402 | Rcc1, Rcc2 |
Power design files
The KiCad project lives in the anton-vinogradov/esp32-leshy2 repository on GitHub; these links point at the commit this page was built from.
Power: common questions
How big is the Power PCB?
The Power measures 90 × 70 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Power?
42 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Power design files?
From the anton-vinogradov/esp32-leshy2 repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Power design in my own project?
Yes, under the terms of its MIT license, which anton-vinogradov chose for the repository.
More boards in esp32-leshy2
Leshy2 LESHY2-RF-R2 R2 exact placement
anton-vinogradov
80 × 150 mm778 parts6LMIT6ESP32
Leshy2 LESHY2-UI-R2 R2 exact placement
anton-vinogradov
80 × 150 mm430 parts6LMIT6Indicators
anton-vinogradov
90 × 70 mm37 parts2LMIT6Audio
anton-vinogradov
80 × 60 mm19 parts2LMIT6Expansion
anton-vinogradov
80 × 60 mm13 parts2LMIT6
Similar boards
Hat
pa3gsb
65 × 56 mm81 parts2LNo license675Radioberry juice
pa3gsb
65 × 56 mm87 parts2LNo license675Radioberry preamp
pa3gsb
65 × 56 mm137 parts2LNo license675Goodwatch20
travisgoodspeed
25.6 × 27.6 mm20 parts2LNo license568GoodPocketWatch
travisgoodspeed
75.2 × 101.2 mm56 parts2LNo license568Goodwatch31
travisgoodspeed
25.6 × 27.6 mm23 parts2LNo license568