Lamp remote mcu
About the Lamp remote mcu PCB
Lamp remote mcu is an open source AVR/Arduino PCB design by ArgonautGit, published on GitHub. It is a 2-layer board measuring 29 × 19 mm, with 9 components from 7 distinct parts.
Its main chip is the ATtiny13A-P, from the AVR/Arduino family. By type, the board carries 4 capacitors, 2 connectors, 1 IC, 1 switch and 1 resistor.
From the project
Just some Kicad projects I've worked on over the years. Most are unfinished or don't work well.
Main components on the Lamp remote mcu
Lamp remote mcu bill of materials (BOM)
9 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ATtiny13A-P | DIP-8_W7.62mm_LongPads | U1 |
| 1 | SCREW TERMINAL | TerminalBlock_bornier-2_P5.08mm | J1 |
| 1 | RX | rx | J2 |
| 1 | SWITCH | SW_PUSH_6mm | SW1 |
| 2 | 100nF | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C2 |
| 2 | 10uF | CP_Radial_D5.0mm_P2.50mm | C3, C4 |
| 1 | 10k | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1 |
Lamp remote mcu design files
The KiCad project lives in the ArgonautGit/kicad-projects repository on GitHub; these links point at the commit this page was built from.
Lamp remote mcu: common questions
What microcontroller does the Lamp remote mcu use?
The Lamp remote mcu is built around the ATtiny13A-P, from the AVR/Arduino family.
How big is the Lamp remote mcu PCB?
The Lamp remote mcu measures 29 × 19 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Lamp remote mcu?
9 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Lamp remote mcu design files?
From the ArgonautGit/kicad-projects repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Lamp remote mcu design in my own project?
The repository has no license, so all rights stay with ArgonautGit. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Lamp remote mcu without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in kicad-projects
Flyback 2
66 × 35 mm22 parts2LNo license0
STM32Audio c
9.5 × 38 mm20 parts2LNo license0
STM32Audio
30 × 30 mm20 parts2LNo license0
Lamp remote
38.5 × 21 mm18 parts2LNo license0
AVR/ArduinoAtmega remote
32.5 × 24 mm13 parts2LNo license0
Transmitter
34 × 17 mm12 parts2LNo license0
STM32Stm32 prototype
31 × 26 mm12 parts2LNo license0
STM32Stm proto 2
39 × 23 mm11 parts2LNo license0
Mc34063 boost converter
34 × 19.8 mm10 parts2LNo license0
Oxyhydro
55 × 32 mm10 parts2LNo license0
Similar boards
AVR/ArduinoMagspoof
samyk
35 × 29 mm11 parts2LNo license4.2k
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoLabrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2k
AVR/ArduinoV4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoModuleV450
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k