AntaresAstroMed

arsenii-g·AntaresAstroMed·hardware/astromed/astromed.kicad_pcb

AntaresAstroMed PCB layout, top view — open source ESP32 board by arsenii-g

About the AntaresAstroMed PCB

AntaresAstroMed is an open source ESP32 PCB design by arsenii-g, published on GitHub under the MIT license. It is a 2-layer board measuring 104.1 × 67.3 mm, with 18 components from 17 distinct parts.

Its main chip is the ESP32_LEFT, from the ESP32 family. By type, the board carries 11 connectors, 5 resistors, 1 jumper and 1 switch.

It belongs with the iot & wireless, sensors and dev boards & breakouts designs in this gallery.

From the project

AstroMed by Team Antares: Arduino and ESP32 astronaut health monitoring with live telemetry, guided daily checks and explainable risk assessments. NASA Space Apps 2026.

Schematic and PCB for the AstroMed shield, a board that replaces the breadboard prototype. It sits on top of an Arduino UNO R3, carries an ESP32 DevKit V1 (30-pin, CP2102) in female headers, and provides connectors for every sensor.

Pin assignments follow firmware/unosensors/config.h, firmware/esp32gateway/config.example.h and firmware/README.md. Any pin change on the PCB must also be made in config.h.

AntaresAstroMed, from the project README
From the project README

AntaresAstroMed bill of materials (BOM)

18 components, 17 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
RC522
J1
1
HC-SR04
J2
1
TILT
J3
1
DHT11
J4
1
RTC_DS1307
J5
1
NTC
J6
1
PULSE
J7
1
ESP32_LEFT
J8
1
ESP32_RIGHT
J9
1
SPARE
J10
1
ESP32_RIGHT_ALT
J11
1
5V->VIN
JP1
1
Push button 6 mm
SW1
2
10K
10k
R1, R3
1
220
R2
1
1k
R4
1
2k
R5

AntaresAstroMed design files

The KiCad project lives in the arsenii-g/AntaresAstroMed repository on GitHub; these links point at the commit this page was built from.

AntaresAstroMed: common questions

What microcontroller does the AntaresAstroMed use?

The AntaresAstroMed is built around the ESP32_LEFT, from the ESP32 family.

How big is the AntaresAstroMed PCB?

The AntaresAstroMed measures 104.1 × 67.3 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the AntaresAstroMed?

18 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the AntaresAstroMed design files?

From the arsenii-g/AntaresAstroMed repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the AntaresAstroMed design in my own project?

Yes, under the terms of its MIT license, which arsenii-g chose for the repository.

Can I test firmware for the AntaresAstroMed without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards