V0.5.0
About the V0.5.0 PCB
V0.5.0 is an open source AVR/Arduino PCB design by ARTS-Laboratory, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 32.6 × 97.2 mm, with 15 components from 14 distinct parts.
Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the water_Battery, SD, switch, pH and Sensor. By type, the board carries 9 ICs, 2 resistors, 1 module, 1 battery holder, 1 diode and 1 capacitor.
It belongs with the sensors, power & battery and rf & radio designs in this gallery.
From the project
An in situ water quality sensor for monitoring water quality
Main components on the V0.5.0
V0.5.0 bill of materials (BOM)
15 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | water_Battery | Battery_Input | U1 |
| 1 | SD | SD | U2 |
| 1 | switch | grounded_switch | U3 |
| 1 | pH | phraails | U4 |
| 1 | Sensor | TDS | U5 |
| 1 | DS3231M+ DS3231M https://www.digikey.com/en/products/detail/analog-devices-inc-maxim-integrated/DS3231M-TRL/2402421 | SOIC-16W_7.5x10.3mm_P1.27mm | U6 |
| 1 | Sensor | Turbidity | U7 |
| 1 | Temp | Temp. | U8 |
| 1 | ~ | GPS Module | U9 |
| 1 | Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 1 | Battery_Cell | battery_holder_10mm | BT1 |
| 1 | LED | LED_D3.0mm | D1 |
| 1 | C | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1 |
| 2 | R | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R2 |
V0.5.0 design files
The KiCad project lives in the ARTS-Laboratory/In-Situ-Water-Quality-Sensor repository on GitHub; these links point at the commit this page was built from.
V0.5.0: common questions
What microcontroller does the V0.5.0 use?
The V0.5.0 is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.
How big is the V0.5.0 PCB?
The V0.5.0 measures 32.6 × 97.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the V0.5.0?
15 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the V0.5.0 design files?
From the ARTS-Laboratory/In-Situ-Water-Quality-Sensor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the V0.5.0 design in my own project?
Yes, under the terms of its CC-BY-SA-4.0 license, which ARTS-Laboratory chose for the repository.
Can I test firmware for the V0.5.0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in In-Situ-Water-Quality-Sensor
PCB V0.6.3
33 × 122.1 mm30 parts2LCC-BY-SA-4.02
Ph sensor
52.1 × 29.2 mm25 parts2LCC-BY-SA-4.02
AVR/ArduinoV0.2 Rough Draft
32.6 × 97.2 mm15 parts2LCC-BY-SA-4.02
AVR/ArduinoV0.1
32.6 × 97.2 mm15 parts2LCC-BY-SA-4.02
AVR/ArduinoWater sensor
48.3 × 101.6 mm12 parts2LCC-BY-SA-4.02
AVR/ArduinoMainboard
41.9 × 55.9 mm12 parts2LCC-BY-SA-4.02
AVR/ArduinoWater sensor1
48.3 × 58.4 mm11 parts2LCC-BY-SA-4.02
AVR/ArduinoWater Quality Sensor
44 × 58.5 mm8 parts2LCC-BY-SA-4.02
Water sensor turbidty
39.4 × 12.7 mm5 parts2LCC-BY-SA-4.02
Similar boards
AVR/ArduinoV4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoModuleV450
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoEasyduino Atmega Nano
Hanqaqa
43.4 × 18 mm30 parts4LCERN-OHL-P-2.0746
AVR/ArduinoEasyduino Atmega
68.8 × 53.6 mm35 parts4LCERN-OHL-P-2.0746
AVR/ArduinoUsbGpib
xyphro
54 × 15 mm21 parts2LMIT683
AVR/ArduinoLumberjack
peej
284.7 × 94.2 mm149 parts2LMIT402