17 open source boards using the Switch
Real designs built with the Switch, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Minimap
lucapoulos
48 × 55.4 mm74 parts4LNo license2ESP32
Main v02
bohlebots
80 × 100 mm68 parts2LGPL-2.01ESP32
Main
ItzJannis
80 × 80 mm49 parts2LGPL-3.01Badge hardware
hackwinkel
100 × 100 mm75 parts2LMIT0NXP
PCB v1
chaxaf
140.8 × 32.1 mm68 parts4LNo license0RP2040/RP2350
Esp32-gps
yvolodym
50 × 50 mm59 parts4LCERN-OHL-S-2.00ESP32
Esp32-controller
yvolodym
100 × 70 mm51 parts4LNo license0RP2040/RP2350
ConvolutiedController
Cyclic007
103.5 × 70 mm19 parts2LApache-2.00AVR/Arduino
Capillary-Tube-Valve-Switch
cegly2444
65 × 95 mm6 parts2LNo license0AVR/Arduino
TubePinchValve
kcsmith-uiuc
65 × 95 mm6 parts2LNo license0AVR/Arduino
V0.1
ARTS-Laboratory
32.6 × 97.2 mm15 parts2LCC-BY-SA-4.02AVR/Arduino
V0.2 Rough Draft
ARTS-Laboratory
32.6 × 97.2 mm15 parts2LCC-BY-SA-4.02AVR/Arduino
V0.5.0
ARTS-Laboratory
32.6 × 97.2 mm15 parts2LCC-BY-SA-4.02LNA915
greearb
11.7 × 8.7 mm24 parts4LGPL-2.01LNA915
JensLiu
11.7 × 8.7 mm24 parts4LGPL-2.01LNA915
deepin-community
11.7 × 8.7 mm24 parts4LGPL-2.00AVR/Arduino
Water Quality Sensor
ARTS-Laboratory
44 × 58.5 mm8 parts2LCC-BY-SA-4.02
How designs wire the Switch
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the Switch connects to, and the resistors, capacitors and other passives placed on it.
- The 3 pin has a series capacitor on 5 of 9 designs, most often 100 pF (then 100 nF).
- Pin 4 has a series capacitor on 3 of 5 designs, most often 100 pF.
- Pin 5 is tied to GND on 3 of 4 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 1pin 1 | Connected to: Signal 38% · not connected 23% · VCC 31% |
|
| 2pin 2 | Connected to: The microcontroller 23% · VCC 31% |
|
| 3pin 3 | Connected to: DW01A 22%, U8205A 22% · not connected 22% |
|
| Pin 4 | Connected to: Signal 60% · not connected 40% |
|
| Pin 5 | Connected to: GND 75% · not connected 25% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include V0.1 by ARTS-Laboratory, Minimap by lucapoulos, Main v02 by bohlebots and LNA915 by greearb.
The Switch in open source designs
The gallery holds 17 open source boards using the Switch from 14 GitHub repositories; a typical one measures about 50 × 70 mm and carries around 24 components.
59% are two-layer designs, the rest use four layers or more, and 71% carry an open source license.
The most starred is Minimap by lucapoulos.
Parts used alongside the Switch
Microcontrollers on boards using the Switch
What boards using the Switch are built for
Switch: common questions
Where can I find a Switch reference design?
Each of the 17 boards on this page is a real design using the Switch. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the Switch 3 pin connected?
The 3 pin has a series capacitor on 5 of 9 designs, most often 100 pF (then 100 nF). Counted from the KiCad layouts of 13 open source designs using the Switch.
How is the Switch pin 4 connected?
Pin 4 has a series capacitor on 3 of 5 designs, most often 100 pF. Counted from the KiCad layouts of 13 open source designs using the Switch.
How is the Switch pin 5 connected?
Pin 5 is tied to GND on 3 of 4 designs. Counted from the KiCad layouts of 13 open source designs using the Switch.
What parts are used alongside the Switch?
The Battery, LNA, SAW, AP2112K-3.3 and Arduino_UNO_R3 appear in the most repositories here.
Which microcontrollers do boards using the Switch use?
Most are built on AVR/Arduino (6), ESP32 (4), RP2040/RP2350 (2) and NXP (1).
How big is a typical board using the Switch?
The median is 50 × 70 mm, and 59% are two-layer designs.
What is the most popular open source board using the Switch?
By GitHub stars, Minimap by lucapoulos, with 2 stars.
Can I simulate one of these boards using the Switch before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.