Minew-MS88SF2-breakout
About the Minew-MS88SF2-breakout
Minew-MS88SF2-breakout is an open source PCB design by atoomnetmarc, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 80.7 × 51.5 mm, with 32 components from 23 distinct parts.
Other key parts include the MS88SF2 and NCP1117LPST33T3G. By type, the board carries 9 resistors, 8 capacitors, 6 diodes, 4 connectors, 2 ICs and 2 switches.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Simple nRF52840 Minew MS88SF2 IEEE802.15.4 module breakout board.
This is a simple breakout board for the nRF52840 Minew MS88SF2 module.
Solder all components except the module. Clean PCB.
Test if 3V3 regulator works by connecting 5V to VIN5V-pin (with 50mA power limit). The board should not use any significant current. Measure the 3V3O-pin, it should be 3.3V.
Do not forget to connect an antenna if using the MS88SF2-U.FL module.
Main components on the Minew-MS88SF2-breakout
Minew-MS88SF2-breakout bill of materials (BOM)
32 components, 23 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MS88SF2 | MS88SF2-handsolder | U1 |
| 1 | NCP1117LPST33T3G | SOT-223-3_TabPin2 | U2 |
| 1 | USB_B | USB_B_OST_USB-B1HSxx_Horizontal | J1 |
| 1 | Conn_ARM_JTAG_SWD_10 | PinHeader_2x05_P2.54mm_Vertical | J2 |
| 1 | Conn_01x02_Male | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | Conn_02x08_Odd_Even | PinHeader_2x08_P2.54mm_Vertical | J4 |
| 1 | Polyfuse 0.5A/6V | Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 2 | SW_Push | SW_SPST_CK_RS282G05A3 | SW1, SW2 |
| 2 | SS14 | D_SMA | D1, D2 |
| 2 | BAV99 | SOT-23 | D3, D4 |
| 1 | LED_RGBA | LED_RGB_3528 | D5 |
| 1 | green | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D6 |
| 4 | 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C7, C8 |
| 2 | 100pF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4 |
| 1 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 1 | 1nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6 |
| 1 | 4R7 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
| 2 | 100R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R10 |
| 1 | 1k2 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 2k2 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R8 |
| 1 | 390R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7 |
| 1 | 1M | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9 |
Minew-MS88SF2-breakout design files
The KiCad project lives in the atoomnetmarc/Minew-MS88SF2-breakout repository on GitHub; these links point at the commit this page was built from.
Minew-MS88SF2-breakout: common questions
How big is the Minew-MS88SF2-breakout?
The Minew-MS88SF2-breakout measures 80.7 × 51.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Minew-MS88SF2-breakout?
32 components, from 23 distinct parts. The full bill of materials is listed on this page.
Where can I download the Minew-MS88SF2-breakout design files?
From the atoomnetmarc/Minew-MS88SF2-breakout repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Minew-MS88SF2-breakout design in my own project?
Yes, under the terms of its Apache-2.0 license, which atoomnetmarc chose for the repository.
Similar boards
88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2k
134pin 7-967288-1
139.7 × 73.7 mm38 parts2LGPL-3.01.2k
Breakout 60pin EEC-IV
139.7 × 62.2 mm15 parts2LGPL-3.01.2k
Breakout 112pin Connector
174 × 58 mm39 parts2LGPL-3.01.2k
Eecv breakout
140.8 × 53.7 mm9 parts4LGPL-3.01.2k
Rj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979