Voltage Sensor Timer
avnguyen08·Monitoring_System·Version_A/Top_Board/Top_Board.kicad_pcb
About the Voltage Sensor Timer PCB
Voltage Sensor Timer is an open source ESP32 PCB design by avnguyen08, published on GitHub. It is a 2-layer board measuring 78.7 × 31 mm, with 15 components from 14 distinct parts.
Its main chip is the ESP32 S3 Feather, from the ESP32 family. By type, the board carries 8 resistors and 4 connectors.
It belongs with the displays & leds and sensors designs in this gallery.
From the project
Various current monitoring software products made on the ESP32 using varied electronic components including: LCDs, external ADC, potentiometers, capacitors, resistors, plug-and-play connectors, and 7 segment displays
Voltage Sensor Timer bill of materials (BOM)
15 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CONN_02X03_TOP_BOTTOM Conn_02x03_Top_Bottom | PinHeader_2x03_P2.54mm_Horizontal | J1 |
| 1 | CONN_01X03_PIN Conn_01x10_Socket | PinSocket_1x10_P2.54mm_Vertical_1 | J2 |
| 1 | SCREW_TERMINAL_01X04 Conn_02x01 | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | DIN-5 Conn_02x03_Top_Bottom | PinHeader_2x03_P2.54mm_Horizontal | J4 |
| 1 | ESP32 S3 Feather | Combined Sockets_1x16_1x12 | ESP1 |
| 1 | Time Sec Pot | SSS_PotentiometerV3 | RV1 |
| 1 | Amp Sec Pot | SSS_PotentiometerV3 | RV2 |
| 1 | 187K R | R_0805_2012Metric | R1 |
| 1 | 25.5K R | R_Axial_DIN0411_L9.9mm_D3.6mm_P12.70mm_Horizontal | R2 |
| 1 | 10K R | R_Axial_DIN0411_L9.9mm_D3.6mm_P12.70mm_Horizontal | R3 |
| 1 | 1.82K R | R_0805_2012Metric | R4 |
| 2 | 80.6K R | R_0805_2012Metric | R5, R7 |
| 1 | 4.7K R | R_Axial_DIN0411_L9.9mm_D3.6mm_P12.70mm_Horizontal | R6 |
| 1 | 22K R | R_Axial_DIN0411_L9.9mm_D3.6mm_P12.70mm_Horizontal | R8 |
Voltage Sensor Timer design files
The KiCad project lives in the avnguyen08/Monitoring_System repository on GitHub; these links point at the commit this page was built from.
Voltage Sensor Timer: common questions
What microcontroller does the Voltage Sensor Timer use?
The Voltage Sensor Timer is built around the ESP32 S3 Feather, from the ESP32 family.
How big is the Voltage Sensor Timer PCB?
The Voltage Sensor Timer measures 78.7 × 31 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Voltage Sensor Timer?
15 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Voltage Sensor Timer design files?
From the avnguyen08/Monitoring_System repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Voltage Sensor Timer design in my own project?
The repository has no license, so all rights stay with avnguyen08. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Voltage Sensor Timer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Monitoring_System
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k