Sigmidi
awhite2000·sigmidi·design/kicad/sigmidi-foot-controller.kicad_pcb
About the Sigmidi PCB
Sigmidi is an open source ESP32 PCB design by awhite2000, published on GitHub under the Apache-2.0 license. It is a 2-layer board, with 46 components from 16 distinct parts.
Its main chip is the Arduino Nano ESP32 ABX00083, from the ESP32 family. Other key parts include the Waveshare 24382 and Pololu S13V10F5 #4083. By type, the board carries 18 resistors, 11 switches, 10 LEDs, 3 ICs, 2 connectors and 2 capacitors.
It belongs with the audio and displays & leds designs in this gallery.
From the project
MIDI Foot Controller
sigmidi-foot-controller.kicadpro is an editable KiCad 10 assembly project. The single A0 landscape sheet contains 46 physical components, 41 named nets and 143 connected terminals. Two additional PWRFLAG symbols declare externally supplied power; they are not purchased parts. All connections use continuous wires. Net labels name those wires, and dots identify junctions. Purchased boards stop at their external pins.
Main components on the Sigmidi
Sigmidi bill of materials (BOM)
46 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Arduino Nano ESP32 ABX00083 | U1 | |
| 1 | Waveshare 24382 | U2 | |
| 1 | Pololu S13V10F5 #4083 | U3 | |
| 1 | 5.5x2.1mm center-negative | J1 | |
| 1 | Amphenol ACJS-MHDC | J2 | |
| 10 | momentary NO | SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8 +2 | |
| 1 | 20-detent rotary encoder + NO click | SW11 | |
| 10 | Pololu 2535 | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8 +2 | |
| 1 | 47uF / 35V | C1 | |
| 1 | 100NF 100nF | C5 | |
| 3 | 10K 10k | R7, R21, R31 | |
| 1 | 20K 20k | R8 | |
| 10 | 1k | R9, R10, R11, R12, R13, R14, R15, R16 +2 | |
| 2 | 5.1K 5.1k | R20, R30 | |
| 1 | 100K 100k | R50 | |
| 1 | 150K 150k | R51 |
Sigmidi design files
The KiCad project lives in the awhite2000/sigmidi repository on GitHub; these links point at the commit this page was built from.
Sigmidi: common questions
What microcontroller does the Sigmidi use?
The Sigmidi is built around the Arduino Nano ESP32 ABX00083, from the ESP32 family.
How big is the Sigmidi PCB?
The Sigmidi has 2 copper layers and is 1.6 mm thick.
How many components are on the Sigmidi?
46 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Sigmidi design files?
From the awhite2000/sigmidi repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Sigmidi design in my own project?
Yes, under the terms of its Apache-2.0 license, which awhite2000 chose for the repository.
Can I test firmware for the Sigmidi without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k