Power mon
baldufal·power_mon
About the Power mon PCB
Power mon is an open source ESP32 PCB design by baldufal, published on GitHub under the MIT license. It is a 2-layer board measuring 125 × 95 mm, with 64 components from 13 distinct parts.
Its main chip is the ESP32-C3_SUPERMINI_TH, from the ESP32 family. By type, the board carries 20 resistors, 18 connectors, 9 transistors, 9 diodes, 5 ICs and 3 fuses.
It belongs with the iot & wireless and sensors designs in this gallery.
From the project
Power monitor based on INA3221 and ESP32 with Tasmota
Care should be taken that the right versions of the ESP32-C3 Super Mini and the INA3221 are selected (see below). The voltage is regulated using a compact 5V volatage regulator module.
The board was fabricated by JLCPCB and soldered by hand.
1. Download the latest version of Tasmota and open it in PlatformIO. 2. Enable I2C and INA3221 drivers in tasmota/userconfigoverride.h by inserting

Main components on the Power mon
Power mon bill of materials (BOM)
64 components, 13 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | ~ | INA3221_Module | U1, U2, U3 |
| 1 | ESP32-C3_SUPERMINI_TH | MODULE_ESP32-C3_SUPERMINI_TH | U5 |
| 1 | ~ | DC_DC_3A_Mini_Aliexpress | U6 |
| 9 | Si2302CDS | SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6, Q10, Q11 +1 |
| 3 | Screw_Terminal_01x06 | TerminalBlock_Phoenix_MKDS-3-6-5.08_1x06_P5.08mm_Horizontal | J1, J5, J9 |
| 9 | Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Vertical | J2, J3, J4, J6, J7, J8, J10, J11 +1 |
| 4 | Conn_01x02_Pin | TerminalBlock_Phoenix_MKDS-3-2-5.08_1x02_P5.08mm_Horizontal | J17, J18, J19, J20 |
| 2 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J21, J22 |
| 3 | Fuse | Fuse Holder 15mm pin distance 5x20 | F1, F2, F3 |
| 9 | LED | LED_D3.0mm | D1, D2, D3, D4, D5, D6, D7, D8 +1 |
| 9 | R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5, R6, R7, R8 +1 |
| 9 | 10k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R13, R14, R15, R18, R19, R21, R23, R24 +1 |
| 2 | 4k7 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R16, R20 |
Power mon design files
The KiCad project lives in the baldufal/power_mon repository on GitHub; these links point at the commit this page was built from.
- LayoutPowerMon.kicad_pcb
- SchematicPowerMon.kicad_sch
Power mon: common questions
What microcontroller does the Power mon use?
The Power mon is built around the ESP32-C3_SUPERMINI_TH, from the ESP32 family.
How big is the Power mon PCB?
The Power mon measures 125 × 95 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Power mon?
64 components, from 13 distinct parts. The full bill of materials is listed on this page.
Where can I download the Power mon design files?
From the baldufal/power_mon repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Power mon design in my own project?
Yes, under the terms of its MIT license, which baldufal chose for the repository.
Can I test firmware for the Power mon without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k