SLAM-Robot

BigBrain244466666·SLAM-Robot·PCB/SLAM Robot.kicad_pcb

SLAM-Robot PCB layout, top view — open source ESP32 board by BigBrain244466666

About the SLAM-Robot PCB

SLAM-Robot is an open source ESP32 PCB design by BigBrain244466666, published on GitHub. It is a 2-layer board measuring 146.5 × 99.4 mm, with 50 components from 32 distinct parts.

Its main chip is the ESP32-DEVKITC, from the ESP32 family. By type, the board carries 10 ICs, 10 capacitors, 9 resistors, 8 switches, 7 diodes and 2 modules.

It belongs with the robotics & motion designs in this gallery.

From the project

A robot that uses cameras to map out a given area then is able to go to anywhere directed on the created map.

I decided to make this project as being able to map out a room seemed really cool. I also saw a video on how newer cars could implement lidar technology for auto driving, and I found that very cool and wanted to try it out.

PCB is extra $20 but will be after components.

SLAM-Robot, from the project README
From the project README

Main components on the SLAM-Robot

SLAM-Robot bill of materials (BOM)

50 components, 32 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
~
U1
1
~
U2
1
ESP32-DEVKITC
U3
2
~
U4, U5
2
~
U6, U7
1
~
U8
2
~
U9, U10
2
Fan
M1, M2
1
Raspberry_Pi_4
J1
1
LiPo 2200mAh 3S Battery
BT1
1
Fuse
F1
1
Speaker
LS1
1
Main Switch
SW1
1
3.3V Switch
SW2
1
5V Switch
SW3
1
Fan Switch
SW4
1
Diagnostics Button
SW5
1
Bluetooth Switch
SW6
1
Motor 2 Switch
SW7
1
Motor 1 Switch
SW8
Show 12 more
QtyPartRefs
1
Main LED
D1
1
5V LED
D2
1
3.3V LED
D3
1
Fan LED
D4
1
Bluetooth LED
D5
1
Motor 2 LED
D6
1
Motor 1 LED
D7
1
C_Polarized
C1
9
C
C2, C3, C4, C5, C6, C7, C8, C9 +1
7
330 Ohm
R1, R2, R3, R4, R5, R8, R9
1
4.7K - 10K
R6
1
R
R7

SLAM-Robot design files

The KiCad project lives in the BigBrain244466666/SLAM-Robot repository on GitHub; these links point at the commit this page was built from.

SLAM-Robot: common questions

What microcontroller does the SLAM-Robot use?

The SLAM-Robot is built around the ESP32-DEVKITC, from the ESP32 family.

How big is the SLAM-Robot PCB?

The SLAM-Robot measures 146.5 × 99.4 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the SLAM-Robot?

50 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the SLAM-Robot design files?

From the BigBrain244466666/SLAM-Robot repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the SLAM-Robot design in my own project?

The repository has no license, so all rights stay with BigBrain244466666. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the SLAM-Robot without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards