ESP32-S2 PCB-Design
chaitravi-ce·ESP32-S2_PCB-Design·ESP32-S2/ESP32-S2.kicad_pcb
About the ESP32-S2 PCB-Design
ESP32-S2 PCB-Design is an open source ESP32 PCB design by chaitravi-ce, published on GitHub under the MIT license. It is a 2-layer board measuring 27.9 × 70 mm, with 38 components from 20 distinct parts.
Its main chip is the ESP32-S2-WROOM-ESP32-S2-WROOM, from the ESP32 family. Other key parts include the CH340C and AMS1117-3.3. By type, the board carries 11 capacitors, 11 resistors, 4 connectors, 4 diodes, 3 ICs and 2 transistors.
From the project
A New PCB Design for ESP32-S2 Board
This repository contains hardware design files and datasheets for the ESP32-S2. This is an ESP32-S2 based PCB with breakout ports for both USB - Type A and USB - Type C.
Small form factor of 70mm x 27.9mm Uses ESP32-S2-WROOM RF module Breakout ports for both USB - Type A and USB - Type C Powering modes for the ESP - Either can be used - USB - A: Using a USB A Male Cable - USB - C: Using a USB C Male Cable(Typical Mobile charger cable) - Vin Pin: Supplying this GPIO pin with external 5V Can use it as a power/communicating device for a joystick/ game controller. Space efficient PCB with…

Main components on the ESP32-S2 PCB-Design
ESP32-S2 PCB-Design bill of materials (BOM)
38 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S2-WROOM-ESP32-S2-WROOM | ESP32S2WROOMM22S2H3200PH3Q0 | U1 |
| 1 | CH340C | SOIC-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U3 |
| 2 | L8050QLT1G | L8050QLT1G | Q1, Q2 |
| 1 | USB_A | USB_A_Wuerth_614004134726_Horizontal | J1 |
| 1 | TYPE-C-31-M-12 | HRO_TYPE-C-31-M-12 | J2 |
| 1 | Conn_01x18_Male | PinHeader_1x18_P2.54mm_Vertical | J3 |
| 1 | Conn_01x22_Male | PinHeader_1x22_P2.54mm_Vertical | J4 |
| 1 | Polyfuse_Small | Fuse_1206_3216Metric | F1 |
| 2 | SW_Push | tactile_smd_switch | SW1, SW2 |
| 1 | BAT760-7 | SOD2513X120N | D1 |
| 3 | LED | LED_0603_1608Metric_Castellated | D2, D3, D4 |
| 1 | 1uF | C_0603_1608Metric | C1 |
| 7 | 0.1uF | C_0603_1608Metric | C2, C4, C5, C6, C7, C9, C11 |
| 1 | 10uF | C_0603_1608Metric | C3 |
| 1 | 10 uF | C_0603_1608Metric | C8 |
| 1 | 22 uF | C_0603_1608Metric | C10 |
| 6 | 10K | R_0603_1608Metric | R1, R2, R4, R5, R7, R8 |
| 2 | 5.1K | R_0603_1608Metric | R3, R6 |
| 3 | 1k | R_0603_1608Metric | R9, R10, R11 |
ESP32-S2 PCB-Design design files
The KiCad project lives in the chaitravi-ce/ESP32-S2_PCB-Design repository on GitHub; these links point at the commit this page was built from.
ESP32-S2 PCB-Design: common questions
What microcontroller does the ESP32-S2 PCB-Design use?
The ESP32-S2 PCB-Design is built around the ESP32-S2-WROOM-ESP32-S2-WROOM, from the ESP32 family.
How big is the ESP32-S2 PCB-Design?
The ESP32-S2 PCB-Design measures 27.9 × 70 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the ESP32-S2 PCB-Design?
38 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the ESP32-S2 PCB-Design design files?
From the chaitravi-ce/ESP32-S2_PCB-Design repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the ESP32-S2 PCB-Design design in my own project?
Yes, under the terms of its MIT license, which chaitravi-ce chose for the repository.
Can I test firmware for the ESP32-S2 PCB-Design without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k