M0
chickadee-tech·m0·pcb/m0.kicad_pcb
About the M0 PCB
M0 is an open source Microchip SAM PCB design by chickadee-tech, published on GitHub under the CC-BY-4.0 license. It is a 2-layer board measuring 36 × 36 mm, with 44 components from 30 distinct parts.
Its main chip is the SAMD21J, from the Microchip SAM family. Other key parts include the TLV70233DBV. By type, the board carries 12 capacitors, 12 resistors, 8 connectors, 5 diodes, 2 ICs and 2 transistors.
From the project
M0 based Polystack control board
You may also license the Polystack logo for free by emailing support@chickadee.tech. We'll ask for your gerbers to ensure the design complies with specifications laid out here and provide written permission to use the trademark after compliance has been demonstrated.
Main components on the M0
M0 bill of materials (BOM)
44 components, 30 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SAMD21J | QFN-64-1EP_9x9mm_Pitch0.5mm | U1 |
| 1 | TLV70233DBV | SOT-23-5 | U3 |
| 2 | Q_NMOS_GSD | SOT-23 | Q3, Q4 |
| 1 | 3V3 | Measurement_Point_Round-SMD-Pad_Small | P1 |
| 1 | CONN_01X06 | Pin_Header_Angled_1x06 | P2 |
| 1 | USB_OTG | Mini-USB-B-EDGE | P3 |
| 1 | CONN_02X10 | DF40-20pin-Header | P5 |
| 1 | RESET | Measurement_Point_Round-SMD-Pad_Small | P6 |
| 1 | BOOT0 | Measurement_Point_Round-SMD-Pad_Small | P7 |
| 1 | CONN_01X01 | Measurement_Point_Square-SMD-Pad_Small | P8 |
| 1 | 5V | Measurement_Point_Round-SMD-Pad_Small | P9 |
| 1 | CKD_SANDWICH | DF40-3-4mm-80pin-Receptacle | PORT_OUT1 |
| 1 | SW_PUSH | SW_SPST_EVQP7A | SW1 |
| 1 | GREEN | LED_0603 | D1 |
| 1 | YELLOW | LED_0603 | D2 |
| 2 | RED | LED_0603 | D3, D5 |
| 1 | D_Schottky_x2_KCom_AAK | SOT-23 | D4 |
| 1 | INDUCTOR_SMALL | Neosid_Inductor_SM0603CG | L1 |
| 2 | 10uF | C_1206_HandSoldering | C1, C4 |
| 6 | 0.1uF | C_0603_HandSoldering | C2, C3, C5, C7, C8, C9 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1uF | C_0603_HandSoldering | C6 |
| 1 | 10uF+ | C_1206_HandSoldering | C11 |
| 1 | 1uF+ | C_0603_HandSoldering | C12 |
| 1 | 2.2uF | C_0603_HandSoldering | C15 |
| 5 | 1k | R_0603_HandSoldering | R1, R2, R3, R4, R12 |
| 1 | 330 | R_0603_HandSoldering | R5 |
| 2 | 10k | R_0603_HandSoldering | R6, R7 |
| 2 | 2k | R_0603_HandSoldering | R8, R11 |
| 1 | 470k | R_0603_HandSoldering | R9 |
| 1 | 100k | R_0603_HandSoldering | R10 |
M0 design files
The KiCad project lives in the chickadee-tech/m0 repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/m0.kicad_pcb
M0: common questions
What microcontroller does the M0 use?
The M0 is built around the SAMD21J, from the Microchip SAM family.
How big is the M0 PCB?
The M0 measures 36 × 36 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the M0?
44 components, from 30 distinct parts. The full bill of materials is listed on this page.
Where can I download the M0 design files?
From the chickadee-tech/m0 repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the M0 design in my own project?
Yes, under the terms of its CC-BY-4.0 license, which chickadee-tech chose for the repository.
Can I test firmware for the M0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Microchip SAM firmware against it before you order a PCB.
Similar boards
Microchip SAM
Microcontroller Expansion Card
FrameworkComputer
26 × 30 mm24 parts2LCC-BY-4.01.1kMicrochip SAM
Taco Raven
VoronDesign
120 × 113 mm349 parts4LGPL-3.01.1kMicrochip SAM
Fpgaboy
Wren6991
50 × 50 mm89 parts4LNo license511Microchip SAM
OpenDropV4
GaudiLabs
124 × 115.4 mm118 parts2LGPL-3.0487Microchip SAM
ModulAdapter universal
GaudiLabs
100 × 69.5 mm45 parts2LGPL-3.0487Microchip SAM
Kira
kiibohd
366.9 × 114.3 mm400 partsCERN-OHL-1.2416