Cave-Uno

Chicken-Fried·Cave-Uno

Cave-Uno PCB layout, top view — open source AVR/Arduino board by Chicken-Fried

About the Cave-Uno PCB

Cave-Uno is an open source AVR/Arduino PCB design by Chicken-Fried, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 53.3 × 68.6 mm, with 66 components from 46 distinct parts.

Its main chip is the ATMEGA328PB-MN, from the AVR/Arduino family. Other key parts include the XDJK-0051-025, LM66100DCKR, AP63205WU-7, USBLC6-2SC6 and CH9101R. By type, the board carries 17 capacitors, 13 resistors, 10 connectors, 8 ICs, 6 diodes and 2 fuses.

It belongs with the power & battery and dev boards & breakouts designs in this gallery.

From the project

Modernized Arduino Uno R3 compatible board powered by Microchip ATmega328PB. Features driverless USB-C, 1.5A sync buck, ideal-diode OR-ing, dual I2C/SPI/UART, and LiDAR topographic artwork. Designed in Europe with KiCad 10.

Cave Uno is a next-generation open-source microcontroller development board engineered in Europe by Cave Rover. Conceived specifically for engineering, electronics, and technical students, as well as makers and university labs, Cave Uno is an upgraded, modern reinterpretation of the iconic Arduino Uno Rev3.

It retains 100% mechanical, electrical, and shield compatibility with the Uno R3 form factor while addressing all classic limitations through modern silicon: reversible USB-C with native plug-and-play driverless operation, a high-efficiency synchronous buck converter, zero-voltage-drop…

Cave-Uno, from the project README
From the project README

Main components on the Cave-Uno

Cave-Uno bill of materials (BOM)

66 components, 46 distinct parts.

QtyPartRefs
1
XDJK-0051-025
LX(连欣科技)
U1
2
LM66100DCKR
TI(德州仪器)
U2, U3
1
AP63205WU-7
DIODES(美台)
U4
1
USBLC6-2SC6
U5
1
CH9101R
WCH(南京沁恒)
U6
1
AP2112K-3.3TRG1
DIODES(美台)
U7
1
ATMEGA328PB-MN
MICROCHIP(美国微芯)
U8
1
AO3401A
AOS
Q1
1
NX2520SA-16MHZ-STD-CSW-5
STD-CSW-5
NDK
X1
1
ICSP1 Header
J1
1
Analog GPIO Header
J2
1
Numeric/Analog GPIO Header 2
J3
1
Numeric GPIO Header
J4
1
Power Header
J5
1
Numeric/Analog GPIO Header 1
J6
1
I2C Header
J7
1
UART Header
J8
1
Power Output Header
J9
1
GND Header
J10
1
1.1A
F1
Show 26 more
QtyPartRefs
1
500mA
F2
1
K3-1296S-J1
韩国韩荣
SW1
1
PTS526SM15SMTR2LFS
C&K
SW2
1
—
UNK_HOLE_1
1
—
UNK_HOLE_2
1
—
UNK_HOLE_3
1
GT-USB-7025
G-Switch(品赞)
USB1
1
WS2812B-2020-V6
worldsemi
LED1
1
SMBJ15CA
D1
1
Red LED
D2
1
Green LED
D3
1
Amber LED
D4
2
Blue LED
D5, D6
1
4.7u
L1
1
10u
C1
9
100n
C2, C6, C7, C8, C9, C14, C15, C16 +1
2
22u
C3, C4
2
10u
C5, C11
1
1u
C10
2
15p
C12, C13
2
100k
R1, R13
3
10k
R2, R5, R7
2
5.1k
R3, R4
4
1k
R6, R9, R11, R12
1
1.5k
R8
1
220
R10

Cave-Uno design files

The KiCad project lives in the Chicken-Fried/Cave-Uno repository on GitHub; these links point at the commit this page was built from.

Cave-Uno: common questions

What microcontroller does the Cave-Uno use?

The Cave-Uno is built around the ATMEGA328PB-MN, from the AVR/Arduino family.

How big is the Cave-Uno PCB?

The Cave-Uno measures 53.3 × 68.6 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Cave-Uno?

66 components, from 46 distinct parts. The full bill of materials is listed on this page.

Where can I download the Cave-Uno design files?

From the Chicken-Fried/Cave-Uno repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Cave-Uno design in my own project?

Yes, under the terms of its CERN-OHL-P-2.0 license, which Chicken-Fried chose for the repository.

Can I test firmware for the Cave-Uno without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

Similar boards